SCIENCE FIRST
®
| 86475 Gene Lasserre Blvd., Yulee, FL 32097 | 800-875-3214 | www.sciencefirst.com | [email protected]
©2010 - v 4/10
SCIENCE FIRST
®
| 86475 Gene Lasserre Blvd., Yulee, FL 32097 | 800-875-3214 | www.sciencefirst.com | [email protected]
699-9950
(70-150)
Therm Bath III
(110 volt)
Important Safeguards:
• Please read all instructions.
• Do not touch hot surfaces. Do not pick up
when in use.
• To protect against electrical shock, do not
immerse cord, plugs or unit in water or other
liquid.
• Unplug unit when not in use and before clean
-
ing. Allow unit to cool before proceeding.
• Do not operate unit with a damaged cord or
plug, or if the appliance malfunctions or has
been damaged in any manner. Return to Sci
-
ence First
®
for examination, repair or adjust
-
ment.
• Do not use outdoors.
• Do not let cord hang over edge of table or
counter or touch hot surfaces.
• Do not place on or near a hot gas or electric
burner, or in a heated over.
• Do not move appliance when filled with hot
liquids.
• Do not use appliance for other than intended
use.
• To disconnect, switch the unit "OFF", then
remove plug from wall outlet.
Updated features:
•Digitally controlled temperature setting
•Temperature reads in Farenheit and Celsius
•Temperature range: 77°F to 176°F
(25°C-80°C)
•Digitally controlled timer with automatic
shut-off
• Styrene Liner
• Spatula
Maintenance:
• The fuse is accessible via the back panel fuse holder.
**Unplug the waterbath before removing the fuse. To
remove the fuse, open the black fuse holder, located
just above the plug outlet and pull out to remove the
fuse. Replace fuse if necessary.
• The water receptacle is not removable. Clean
often
with any suitable stainless steel cleaner. (We recom
-
mend
Science First
®
29-0701
Stai-Clean 15 oz.
aerosol spray stainless steel cleaner.)
Caution:
Do
not immerse
in water
Corrosion should not
be a problem since the unit is
constructed of 18-8 nickel-bearing stainless steel. The
water receptacle is sealed below the rim so that accidental
spillage is prevented from penetrating to the inside.
How To Use:
1.)Fill reservoir
to a level which will allow the water
to rise without overflowing when the largest object is im
-
mersed. **
Important: To avoid damage, always keep
water level at least half full.
2.)Connect to
110-120v 60 Hz
outlet.
3.)Turn unit on by pushing Rocker Switch located
below red LED lamp. The Rocker Switch will stay il
-
luminated as long as it is in the down position.
4.)To set the desired temperature, press the "Set" but
-
ton. The entire display will begin to flash. Press the "up"
and "down" keys until the desired temperature is reached.
Press the "Set" button again to lock in the new tempera
-
ture. The display will now show the set temperature in
the upper right corner. It will read "Set: (temperature)".
5.)When the therm bath is heating, the display will
read "heating" and show the current temperature in the
main part of the display. The red LED lamp above the
rocker switch will illuminate when the unit is heating,
and go dark when the unit is holding temperature.
Description:
The new and improved thermbath is now a
digital-
ly
controlled warm-water bath. Use for any procedure
where
medium heat
is required.
The therm bath is capable of heating from 77° F to
176°F . The unit can be converted to degrees Celsius
(25°C-80°C) by the touch of the "F/C" buttton.
