manualshive.com logo in svg

Schwinn Airdyne AD2, Руководство по обслуживанию

Поделиться
Скачать
Schwinn Airdyne AD2 Скачать руководство пользователя страница 19

19

Note:

  Your machine may not match the image. For reference only.

To remove the Front Fan Cover:

Tools required:

 pedal wrench, #2 Phillips screwdriver

1.

  Remove the Pedals. Refer to the “Replacing the Pedals” 

procedure in this manual.

2.

  Carefully remove the Shrouds. Refer to the “Replacing the 

Shrouds and Vent Cover” procedure in this manual. Set the 

hardware safely aside for reassembly.

 Note: 

  The hardware that attaches the Front Fan Cover is 

removed during Shroud removal.

3.

  Slide the Front Fan Cover forward to disengage the tabs from 

the Frame brackets. Lift slightly to disengage from the screws 

inside the Frame uprights, and remove it.

4. 

Installation is the reverse procedure.  

 Note: 

  Be sure the Frame brackets go into the tabs on the Front 

Fan Cover.

Disconnect the data cable from the console before you service this machine.

Replacing the Fan Covers

Содержание Airdyne AD2
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды