manualshive.com logo in svg

Schweitzer Engineering SEL-387-0, Инструкция по эксплуатации


Поделиться
Скачать
background image

4.7

Date Code 20170601

Instruction Manual

SEL-387-0, -5, -6 Relay

Control Logic

Multiple Setting Groups

The REMOTE switch position de-energizes all relay inputs, thus placing all of 
the SS

n

 variables in state 0. With none of the SS

n

 variables asserted, the 

GRO

n

 command, or the 

{GROUP}

 pushbutton on the front panel, can be used 

to change the setting group. With the switch in any other position, 1 through 6, 
the 

GRO 

n

 and 

{GROUP}

 functions will not effect a group change.

The setting TGR, the group change delay setting, should be set long enough so 
that the switch, as it is rotated from one position to another, will not remain at 
any intermediate position long enough to make any setting group change. For 
example, in rotating from position 1 to position 5, the switch must pass 
through positions 2, 3, and 4. It should not remain in 2, 3, or 4 for longer than 
TGR during this process, or it may produce multiple group changes before it 
finally gets to position 5.

The settings in 

Table 4.3

 are made in the Global settings area.

CHSG Relay Word Bit 
Asserts During 
Setting Group 
Changes

The Relay Word bit CHSG is asserted whenever a setting group change is in 
process. It is defined in 

Table 4.9

 and 

Table 4.11

 as “Timing to change setting 

groups.” When group changes are initiated through one of the SS

n

 SEL

OGIC

 

control equation settings, CHSG is asserted as soon as the new SS

n

 bit is 

asserted and the relay has made the decision to change groups. It deasserts 
when the SG

n

 bit for the new group agrees with the SS

n

 bit, indicating that the 

relay has changed to the newly requested group number. For example, assume 
the relay is in group 1. The active group bit SG1 equals one, while other SG

n

 

bits are zero. All of the SS

n

 bits are also zero. SS4 is asserted, requesting a 

change to group 4. Since SS1 (same group as the active group) is not asserted, 
the group change process is initiated, and CHSG is asserted at the same time 
as SS4. After the group change is made, SG1 will deassert and SG4 will 
assert, indicating the relay is now in group 4. When this agreement of SS4 and 
SG4 occurs, CHSG will deassert to indicate the relay is no longer in the 
process of changing groups.

When the active group bit SG

n

 and its associated SS

n

 bit are both asserted, for 

example SG1 and SS1, the relay does not respond to the assertion of a new 
SS

n

 bit, such as SS3, and no group change will occur. Similarly, the CHSG bit 

will not assert along with SS3, since the SG1 and SS1 bits are in agreement. 
This agreement acts like a continuous “reset” applied to the CHSG bit.

In applications where a system-related condition requires that a change of 
setting groups must be done quickly and automatically, this would likely be 
accomplished via a contact input to the relay, which would assert an SS

n

 bit. 

In such cases, it may be desirable to immediately block some relay elements 
as soon as the change is needed to prevent misoperation. This could easily be 
done via the CHSG bit. CHSG could be used, for example, to supervise the 
tripping variable for differential trips. The default TR4 setting is TR4 = 87R + 
87U; this could be changed to TR4 = 87R * !CHSG + 87U * !CHSG. CHSG 
optimizes (in this case minimizes) the amount of time to block TR4, since 
CHSG asserts exactly when the change of groups is needed, and deasserts 
exactly when the change has taken place.

Table 4.3

SEL

OGIC

 Control Equation Settings for Rotating Selector Switch

SS1 = !IN103 * !IN102 * IN101

= NOT(IN103) * NOT(IN102) * IN101

SS2 = !IN103 * IN102 * !IN101

= NOT(IN103) * IN102 * NOT(IN101)

SS3 = !IN103 * IN102 * IN101

= NOT(IN103) * IN102 * IN101

SS4 = IN103 * !IN102 * !IN101

= IN103 * NOT(IN102) * NOT(IN101)

SS5 = IN103 * !IN102 * IN101

= IN103 * NOT(IN102) * IN101

SS6 = IN103 * IN102 * !IN101

= IN103 * IN102 * NOT(IN101)

Содержание SEL-387-0













































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-387-0

Torklift C2213 Installation Instructions Manual preview
C2213
Бренд: Torklift Страницы: 17
Hendrickson OPTIMAAX Service Instructions Manual preview
OPTIMAAX
Бренд: Hendrickson Страницы: 24
Sony LBT-ZUX9 - Mini Hifi Component Specifications preview
LBT-ZUX9 - Mini Hifi Component
Бренд: Sony Страницы: 2
Sony LBT-GPX77 Specifications preview
LBT-GPX77
Бренд: Sony Страницы: 4
Sony LBT-GPX55 Specifications preview
LBT-GPX55
Бренд: Sony Страницы: 4
Sony HVL-10NH Instruction & Operation Manual preview
HVL-10NH
Бренд: Sony Страницы: 2
Sony LBT-GPX55 Operating Instructions Manual preview
LBT-GPX55
Бренд: Sony Страницы: 44
Sony LBT-ZUX9 - Mini Hifi Component Operating Instructions Manual preview
LBT-ZUX9 - Mini Hifi Component
Бренд: Sony Страницы: 64
Sony HCD-CBX1 - Compact Disc Receiver Service Manual preview
HCD-CBX1 - Compact Disc Receiver
Бренд: Sony Страницы: 76
Aiwa Z-L20 Service Manual preview
Z-L20
Бренд: Aiwa Страницы: 11
Innovatione 1S PRO Instructions Manual preview
1S PRO
Бренд: Innovatione Страницы: 21
Oase biOrb AIR 60 Operating Instructions Manual preview
biOrb AIR 60
Бренд: Oase Страницы: 166
Ramsey Winch QUICK MOUNT 9000 Owner'S Manual preview
QUICK MOUNT 9000
Бренд: Ramsey Winch Страницы: 12
Current Satellite Freshwater LED Flex Manual preview
Satellite Freshwater LED Flex
Бренд: Current Страницы: 3
Daewoo BH090 Manual preview
BH090
Бренд: Daewoo Страницы: 261
Omron V720S-BC5D4A User Manual preview
V720S-BC5D4A
Бренд: Omron Страницы: 149
RTS Fiber Optic Interface Back Card Installation Instructions preview
Fiber Optic Interface Back Card
Бренд: RTS Страницы: 2
Audiovox ACC56M Owner'S Manual And Installation Manual preview
ACC56M
Бренд: Audiovox Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды