manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

9.42

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Protocols

Serial Distributed Network Protocol (Serial DNP3)

Step 11. Perform an 

AUTO 1

 command on the SEL-2032 and you will 

see a response similar to that in 

Figure 9.5

 indicating that Fast 

SER data is available.

Step 12. Configure the SEL-421 SER function to monitor the circuit 

breaker position contact called 52AA1 inside the relay as SER 
point 1.

Step 13. Configure automatic messaging for the lower-tier SEL-2032 

Port 3 to collect 20TARGET data.

This data will act as present state data during SEL-2032 
initialization.

Step 14. On the upper-tier SEL-2032, enter the following math/

movement statement on Port 16 (52AA1 is set as SER point 1 
in the SEL-421 Relay):

0:1 = 2:STATE:1.0

Step 15. Collect event data with the DNP3 master.

If a trip-reclose-trip event occurs with the circuit breaker 
connected to the SEL-421 on the lower-tier SEL-2032, the 
DNP3 master will receive three time-stamped events, one for 
each circuit breaker trip and close.

The syntax used for the two-tier system is described generically:

a.b = x:STATE:y.z

where the variables have the uses listed in 

Table 9.24

.

When configuring a two-tier system, you will need SER point numbers from 
the device connected to the lower-tier SEL-2032. To obtain these, print or 
display the SER settings for the device. The point number is the number of the 
input point, starting with the first point assigned to the SER. For example, in 
an SEL-300 series relay, the first point assigned in the SER1 setting (that 
contains several SER assignments) is point 1. For an SEL-421, each SER 
point is configured in a separate setting line. To find the point number, count 
from the first point starting with one to the point that you are going to 
configure.

Table 9.24

Two-Tier Fast SER Math/Movement Statement Parameters

Parameter

Definition

a

User Region destination register

b

User Region destination bit of destination register

x

Port connected to lower-tier SEL-2032

y

Port on lower-tier SEL-2032 where Fast SER device is connected

z

SER point number in device (see following discussion)

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

ABB RELION REF615R Manual preview
RELION REF615R
Бренд: ABB Страницы: 66
Maco Standard Fitting Instructions Manual preview
Standard
Бренд: Maco Страницы: 38
Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Бренд: Canon Страницы: 32
Rabbit 2000 Reference Manual preview
2000
Бренд: Rabbit Страницы: 120
D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 5
Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Бренд: Lantronix Страницы: 8
ekwb EK-FC780 GTX Jetstream Installation And Mounting Manual preview
EK-FC780 GTX Jetstream
Бренд: ekwb Страницы: 2
e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Бренд: e-con Systems Страницы: 9
Teac HD-35NAS User Manual preview
HD-35NAS
Бренд: Teac Страницы: 20
Maple Systems cMT-FHDX Series Installation Instruction preview
cMT-FHDX Series
Бренд: Maple Systems Страницы: 2
NETGEAR Powerline 100 Installation Manual preview
Powerline 100
Бренд: NETGEAR Страницы: 2
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Бренд: IDT Страницы: 11
MF DIGITAL DIRECTOR PRO series Operator'S Manual preview
DIRECTOR PRO series
Бренд: MF DIGITAL Страницы: 79
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Бренд: impinj Страницы: 60
Tait TM9000 Installation Instructions Manual preview
TM9000
Бренд: Tait Страницы: 8
C4i GEN-1 Quick Operation Manual preview
GEN-1
Бренд: C4i Страницы: 5
Kaptia Klever Getting Started preview
Klever
Бренд: Kaptia Страницы: 14
Navitar 1-62645 Dimensional Drawing preview
1-62645
Бренд: Navitar Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды