manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

8.14

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Serial Port Communications and Commands

Command Set

The bit labels are listed in most-significant to least-significant bit order, the 
same as in SEL relays. Bit labels are available in the GLOBAL, LOCAL, and 
TARGET (if not in archive) regions.

MEMORY

The 

MEMORY

 command (Access Level 1) displays the status of all 

dynamically allocated memory. This includes RAM, which is used for 
temporary data storage; EEPROM, where string and SEL

OGIC

 control equation 

settings are stored; nonvolatile Flash, where archive data are stored; and 
Shared RAM, where the database is stored. The report indicates the number of 
bytes of dynamic memory, the number of free (unused) bytes, the number of 
free blocks (contiguous segments of unused memory), and the size of the 
largest free block. The screen in 

Figure 8.22

 shows a typical 

MEM

 report.

*>>

MEM <Enter>

Memory        Total      Bytes    Blocks  Largest block
type          bytes      free     free      available

RAM           275536     196678        2      176980
EEPROM         34820      34656        2       34624
ARCHIVE      1835008    1000000        1     1000000
DATA
SET M         128000     100000        1      100000
SETTINGS
SRAM         1046524     789420        1      789420

*>>

Figure 8.22

MEM Command

You can use the free bytes and largest available block to determine if you are 
running out of memory. The number of free blocks indicates how badly the 
memory is fragmented. The more free blocks there are, the less efficiently the 
SEL-2032 can use the available free memory.

MODMAP

The 

MODMAP

 command (Access Level 1) displays the Modbus

®

 Read 

Input Register map of a specific region. The MODMAP display format is 
similar to the example Modbus data map tables in 

Section 9: Protocols

.

The command syntax is:

MOD port number:region_name map_type

where:

➤

port numbers are 1–18

➤

region_names are BREAKER, DEMAND, HISTORY, 
METER, TARGET, and USER

➤

map_type is either F or I, corresponding to floating map and 
integer map. 

Figure 8.23

 is an example of the MODMAP display for Port 2 Meter region 

using an integer map.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

3Com 486 Getting Started Manual preview
486
Бренд: 3Com Страницы: 20
ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Бренд: ICP DAS USA Страницы: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Бренд: ICP DAS USA Страницы: 24
LaCie 5big Network 2 Datasheet preview
5big Network 2
Бренд: LaCie Страницы: 4
LaCie d2 Network 2 Datasheet preview
d2 Network 2
Бренд: LaCie Страницы: 4
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Бренд: RuggedCom Страницы: 42
SIIG FireWire 800 + Hi-Speed USB Combo Quick Installation Manual preview
FireWire 800 + Hi-Speed USB Combo
Бренд: SIIG Страницы: 20
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Бренд: Infoblox Страницы: 13
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Бренд: Z3 Technology Страницы: 67
ATEN Slideaway CL1008 User Manual preview
Slideaway CL1008
Бренд: ATEN Страницы: 77
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Бренд: LevelOne Страницы: 3
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Бренд: Comtrend Corporation Страницы: 4
Xilinx MP3 NG Application Note preview
MP3 NG
Бренд: Xilinx Страницы: 27
ENERMAX ELC-LMT120-RGB User Manual preview
ELC-LMT120-RGB
Бренд: ENERMAX Страницы: 33
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Бренд: IEI Technology Страницы: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Бренд: RadioSPECTRAL Страницы: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Бренд: ZALMAN Страницы: 9
Cypress Semiconductor CY7C1381DV25 Specification Sheet preview
CY7C1381DV25
Бренд: Cypress Semiconductor Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды