Schweitzer Engineering SEL-2032 Скачать руководство пользователя страница 226

Страница: 226 / 354

8.10

SEL-2032

Communications Processor

Instruction Manual

Date Code 20120126

Serial Port Communications and Commands

Command Set

FILE

Use the

FILE

command (Access Level 1 and 2) to perform file operations on

the SEL-2032 file system. See

Table 8.2

. for variations of the

FILE

command.

All text enclosed in [brackets] indicate optional command line parameters.
The

FILE

command allows access to second level subdirectories as the

optional

directory2

parameter.

The SETTINGS directory is the only file directory in the SEL-2032. For

FILE READ

operations, specify the

directory1

(and

directory2

) parameters

as needed. The

FILE WRITE

command is available only for the second-level

subdirectories of the SETTINGS directory. Parameter

filename

is optional for

FILE WRITE

operations. If

filename

is not specified, the file name must be

given in the Ymodem header. When using the

FILE WRITE

command, you

should use only file names that already exist in the relay.

HELP

The

HELP

command (Access Level 0), as shown in

Figure 8.15

, lists all

commands available at the current access level with a one-line description of
each, as shown in the display below. Use the

HELP

command with another

command as its parameter and it will provide the syntax and a brief
description of the command. If you use the

HELP

command with an invalid

command parameter, the SEL-2032 responds with an error message.

HELP <Enter>

Commands available at current access level:

- ACCESS - Change access level to Access Level 1
- HELP - Provide information on available commands
- ID - Display SEL-2032 identification information
- QUIT - Change access level to Access Level 0

Figure 8.15

HELP Command

The SEL-2032 responds to the

command (Access Level 0) with

identification information, including the following:

FID

SEL-2032 firmware identification string

BFID

SEL

BOOT

firmware identification string

CID

SEL-2032 firmware checksum

DEVID

ID as set in the global settings

Table 8.2

Variations on the FILE Command

Command

Action

Format

Applications

FILE DIR

Perform directory
operations.Wild-
cards (* ?) are sup-
ported.

FILE DIR [

directory1

[

directory2

]]

Returns a list of filenames in specified directory
(

directory1

) and subdirectory (

directory2

). If nei-

ther parameter is specified, then the list of files and
directories in the root directory is returned.

FILE READ

Read a file from
the SEL-2032

FILE READ [

directory1

[

directory2

]]

filename

Initiates a file transfer of the file

filename

(in the

folder

directory1

, subdirectory

directory2

) from the

SEL-2032 to external support software. The

file-

name

parameter is required.

FILE WRITE

Write a file to the
SEL-2032.

FILE WRITE [

directory1

[

directory2

]]

[

filename

]

Initiates a file transfer of the file

filename

(in the

folder

directory1

, subdirectory

directory2

) from

external support software to the SEL-2032. If the

filename

parameter is not specified, the file name

must be given in the Ymodem header.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации

Результаты поиска

Содержание SEL-2032

Отзывы:

Похожие инструкции для SEL-2032

Бренды по названию

Популярные бренды