manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

8.8

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Serial Port Communications and Commands

Command Set

*>>

DATE 03/20/94 <Enter>

03/20/94
*>>

Figure 8.10

DATE Command

If you use IRIG-B, the day of the year determined from IRIG-B overrides the 
date settings.

DCF

The 

DCF

 command (Access Level 1) enables or disables virtual terminal 

(VT) data collection. This feature allows you to perform data collection 
through the SEL-2701 Ethernet Processor in a similar manner that you would 
through an SEL-2032 serial port. Use the 

DCF ON

 command to enable VT 

data collection and 

DCF OFF

 command to disable VT data collection (see 

Figure 8.11

). The 

DCF

 command must be entered via the VT connection from 

which you want to collect data. Only one DCF session can be enabled on port 
17 or 18.

*>>

DCF ON <Enter>

Data collection features enabled

*>>

Figure 8.11

DCF Command

The 

DCF

 command also supports a NOECHO parameter. When the 

NOECHO parameter is set, the virtual terminal does not echo characters as 
long as DCF is enabled.

*>>

DCF ON NOECHO <Enter>

Data collection features enabled

*>>

Figure 8.12

DCF Command With NOECHO Parameter

DEFRAGMENT

The 

DEFRAGMENT

 command (Access Level 2) defragments EEPROM. 

The SEL-2032 settings are stored in EEPROM. After multiple settings 
changes, the available portion of EEPROM may become fragmented 
(available bytes exist as several small blocks as opposed to a single larger 
block). The 

DEFRAGMENT

 command, as shown in 

Figure 8.13

, may be 

necessary in order to allow further settings changes to be successfully saved.

*>>

DEFRAGMENT <Enter>

Performing EEPROM defragmentation will suspend most SEL-2032 activities.

Perform EEPROM defragmentation (Y/N)? 

Y <Enter>

Defragmenting ... complete.

*>>

Figure 8.13

DEFRAGMENT Command

Executing the 

DEFRAGMENT

 command will momentarily suspend many of 

the SEL-2032 database and communications activities while the SEL-2032 
concentrates the available EEPROM into a single block. Use the 

MEM

 

command to check EEPROM fragmentation.

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Accuphase AD-60 Instruction Manual preview
AD-60
Бренд: Accuphase Страницы: 2
ADTRAN ATLAS 550 Manual preview
ATLAS 550
Бренд: ADTRAN Страницы: 2
Acrosser Technology AMB-VDX3H1 Series Quick Start Manual preview
AMB-VDX3H1 Series
Бренд: Acrosser Technology Страницы: 4
Parker ACR1200 Hardware Manual preview
ACR1200
Бренд: Parker Страницы: 50
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Бренд: Lanner electronics Страницы: 59
Analog Devices EZ-Extender Analog 120-Pin Probing Board Manual preview
EZ-Extender Analog 120-Pin Probing Board
Бренд: Analog Devices Страницы: 29
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Бренд: Orolia Страницы: 167
Patton electronics Model 2711 User Manual preview
Model 2711
Бренд: Patton electronics Страницы: 13
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Бренд: Danville Signal Processing Страницы: 35
NCR 7702-K134 Upgrade Manual preview
7702-K134
Бренд: NCR Страницы: 15
Concept Pro DEEP LEARNING PLUS Quick Start Manual preview
DEEP LEARNING PLUS
Бренд: Concept Pro Страницы: 28
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Бренд: GSA Страницы: 101
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Бренд: Microchip Technology Страницы: 41
Dinstar UC8000 IPPBX User Manual preview
UC8000 IPPBX
Бренд: Dinstar Страницы: 103
Alvarion BreezeNET DS.11 Configuration Utility Release Note preview
BreezeNET DS.11 Configuration Utility
Бренд: Alvarion Страницы: 2
Beck com.tom INDUSTRY 100.WLAN.W Startup Manual preview
com.tom INDUSTRY 100.WLAN.W
Бренд: Beck Страницы: 2
Valcom VIP-814 Installation Manual preview
VIP-814
Бренд: Valcom Страницы: 3
Renesas PCA7755D User Manual preview
PCA7755D
Бренд: Renesas Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды