manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Инструкция по эксплуатации


Поделиться
Скачать
background image

8.2

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Serial Port Communications and Commands

Command Operation

<STX><MESSAGE LINE 1><CR><LF>
 <MESSAGE LINE 2><CR><LF>

 .
 .
 .

<LAST MESSAGE LINE><CR><LF>
<ETX><STX> <PROMPT><ETX>

Figure 8.1

Noninteractive Message Format

Each message begins with the start-of-transmission character STX (ASCII 
character 02) and ends with the end-of-transmission character ETX (ASCII 
character 03). Each line of the message ends with a carriage return and line 
feed.

➤

The CAN character (ASCII character 24) aborts a pending 
transmission. This capability is useful in terminating an 
unwanted transmission.

➤

You can send control characters from most keyboards with the 
following keystrokes:

XON:

 <CTRL+Q> 

(hold down the Control key and press Q)

XOFF: 

<CTRL+S>

 (hold down the Control key and press S)

CAN: 

<CTRL+X>

 (hold down the Control key and press X)

Command 
Access Levels

A multilevel password system with three access levels provides security 
against unauthorized access. This system allows you to give personnel access 
only to those functions they require. The password system is disabled when 
the password jumper is inserted on the main board of the SEL-2032. See 

Jumper Settings on page 2.1

 for information on using this jumper. Passwords 

can be set or disabled on an access level basis using the 

PASSWORD

 

command, described in 

PASSWORD on page 8.15

.

Each level has an associated screen prompt that indicates the active level. 

Table 8.1

 shows the access levels of the prompts as well as the commands 

available from each access level.

WARNING:

 This device is 

shipped with default passwords. 

Default passwords should be 
changed to private passwords at 
installation. Failure to change each 
default password to a private 
password may allow unauthorized 
access. SEL shall not be responsible 
for any damage resulting from 
unauthorized access.

!

Table 8.1

Access Level Characteristics 

 (Sheet 1 of 2)

Access Level

0

1

2

Prompt

*

*>

*>>

Available 
Commands

ACCESS

2ACCESS

ACCESS

AUTO

BROADCAST

CLEAR

2ACCESS

ACCESS

AUTO

BROADCAST

CAL

CARD

CLEAR

CONTROL

COPY

DATE

DATE

DEFRAG

DCF

a

DCF

DNPMAP

FILE

DNPMAP

FILE

Courtesy of NationalSwitchgear.com

Содержание SEL-2032



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SEL-2032

Mackie SP260 Installation Instructions preview
SP260
Бренд: Mackie Страницы: 2
Mackie SP260 Product Overview preview
SP260
Бренд: Mackie Страницы: 5
peplink balance ONE Manual preview
balance ONE
Бренд: peplink Страницы: 2
National Instruments SCXI-1120 User Manual preview
SCXI-1120
Бренд: National Instruments Страницы: 130
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Бренд: Lindsay Broadband Страницы: 4
Patton electronics Model 2711 User Manual preview
Model 2711
Бренд: Patton electronics Страницы: 13
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Бренд: Paradyne Страницы: 10
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Бренд: Arbor Technology Страницы: 8
Kontron ePanel-C3 Technical Manual preview
ePanel-C3
Бренд: Kontron Страницы: 62
ATI Technologies Radeon Online Manual preview
Radeon
Бренд: ATI Technologies Страницы: 87
Areca ARC-12x4 Series Quick Installation Manual preview
ARC-12x4 Series
Бренд: Areca Страницы: 2
Altimium CVHH2 User Manual preview
CVHH2
Бренд: Altimium Страницы: 12
AMC DSP 88 User Manual preview
DSP 88
Бренд: AMC Страницы: 28
Serial Cables PCI-AD-x16HE-BG4 User Manual preview
PCI-AD-x16HE-BG4
Бренд: Serial Cables Страницы: 18
Multitech MultiModem ISIHP-2S User Manual preview
MultiModem ISIHP-2S
Бренд: Multitech Страницы: 155
COMBA TB-1800 Equipment Manual preview
TB-1800
Бренд: COMBA Страницы: 57
WATT & WELL SECC Series Getting Started preview
SECC Series
Бренд: WATT & WELL Страницы: 15
FabiaTech FB2510 Series User'S Quick Setting preview
FB2510 Series
Бренд: FabiaTech Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды