Schweitzer Engineering Laboratories SEL-734W Скачать руководство пользователя страница 43

Страница: 43 / 48

Date Code 20191029

Field Reference Guide

SEL-734W and SEL Wireless Current Sensor

Instruction Manual

S E C T I O N

Testing and Troubleshooting

Table 7.1

provides instructions for troubleshooting and common problems.

Table 7.1

Troubleshooting and Common Problems

Problem

Solution

OPEN

Button

Does Not Respond

➤

Check that the Manual mode is enabled. Press the

MANUAL

pushbutton to enable this mode.

➤

Check that the control power is healthy.

➢

Check that the control power fuse located on the inside of the enclosure has continuity.

➢

Check that 120 Vac is present. Refer to the enclosure wiring and check that 120 Vac voltage is pres-
ent between the control power fuse and neutral.

➢

Check the front panel. Refer to the appropriate design template guide to check the SEL-734W indi-
cators of control power.

➤

Check that an overvoltage does not exist. To protect the switches and the capacitor bank, the controller
will not close a switch if an overvoltage condition exists. Refer to

SEL-734W Template Reference Guide

to check the SEL-734W lockout indicators.

Содержание SEL-734W

















































Результаты поиска

Содержание SEL-734W

Отзывы:

Похожие инструкции для SEL-734W

Бренды по названию

Популярные бренды

Schweitzer Engineering Laboratories SEL-734W, Справочник по полевым условиям эксплуатации

Результаты поиска

Содержание SEL-734W

Отзывы:

Похожие инструкции для SEL-734W

Бренды по названию

Популярные бренды