Schwan SC80 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

Schwan SC80 Скачать руководство пользователя страница 10

10

Schwan Dispenser

PRV

Cold water inlet with

15mm Stop tap

by plumber

Filter

system

10 amp plug in

power supply

SC80 chiller

unit

Power cord

Drained safe tray

of cabinet

Warm air outlet vent

in door of cabinet

CO2 regulator

CO2 black 6mm tube

Chilled water to tap blue 1/4” tube

Soda water

to regulator

white 1/4” tube

Soda water to tap

Soda regulator

white 1/4” tube

cold water supply to

chiller blue 1/4” tube

Typical installation layout

In situations where any water leakage could result in damage to property, the

complete Schwan installation should be installed over a Drained Safe Tray,

plumbed to an appropriate drainage connection.

WARNING

NOTE

Allow a minimum of 100mm air space around the sides,

back and the front of the chiller.

Cabinet must be vented to provide air flow, see venting

diagram on next page.

The filter system and CO2 bottle must be easily accessible

for routine maintenance and changing.

The filter must be less than 600mm from the chiller inlet.

Use no more than 800mm of 1/4” water supply tube from

stop tap to chiller inlet.

Tap base must be within 700mm of chiller outlet

•

•

•

•
•

•

«
...
8
9
10
11
12
...
»

Содержание SC80

































Отзывы:

Нет отзывов