INSPECTION CAMERA IPK124 - OPERATING INSTRUCTIONS
Intended Use
The inspection camera is an optical device. There is an integrated
mini colour camera with dimmable LED lighting at the bottom of the
waterproof gooseneck. The camera image is displayed on the
integrated TFT monitor. A NTSC video output is available. The
Inspection camera is a visual tool designed for optical error
diagnostics and inspection on facilities and appliances that are
voltage free. Using the flexible gooseneck, the colour camera,
situated on the top of the device, can be moved into inaccessible
positions and areas. Two white LEDs enable image capture, even
in totally dark areas. The gooseneck and the camera head are
waterproof and suitable for use in aqueous liquids (not acids or
alkalis). The maximum immersion depth is 90 cm. Do not expose
the handle and the monitor to moisture or submerge them.
The Inspection camera is powered by 4 AA batteries. Do not use in
explosive areas or on persons or animals. Any other use than
described above is not permitted, it could cause damage to the
product and personal injury. No part of the product may be
modified or rebuilt! The safety instructions are to be observed
without fail!
Safety Instructions
Please read all of the operating instructions before
using the product for the first time; they contain
important information about the correct operation.
The warranty will be void in the event of damage
caused by failure to observe these safety instructions! We do
not assume any liability for any cones-quential damage! We
do not assume any liability for material and personal damage
caused by improper use or non-compliance with the safety
instructions! The warranty will be void in such cases.
This device left the manufacture’s factory in a safe and perfect
condition. We kindly request the user to observe the safety
instructions and warnings contained in these operating instructions
to preserve this condition and to ensure safe operation. Please pay
attention to the following symbols:
An exclamation mark in a triangle indicates important
information in these operating instructions which is to be
observed without fail.
This product has been CE tested and complies with the
required European guidelines.
A „hand“ symbol is used to indicate where specific hints
and information on handling are given.
The unauthorized conversion and/or modification of the product is
inadmissible for reasons of safety and approval (CE). When not in
use, store the Inspection camera in the carrying case. Sensitive
surfaces might cause chemical reactions with the housing. Avoid
as well strong mechanical strains or vibrations. Make sure you
never go below the minimum bending radius of 45mm.
Keep the unit out of the reach of children. It is not a toy. Do not
leave packaging materials unattended. They could become a
dangerous playthings for children. On industrial sites, the accident
prevention regulations of the association of the industrial workers’
society for electrical equipment and utilities must be followed. Only
immerse the camera head and gooseneck in liquids that are
voltage free! The immersion depth must not exceed approx. 90 cm.
Please pay attention to the markings on the gooseneck. If you have
a reason to believe that the device can no longer be operated
safely, disconnect it immediately and secure it against being
operated unintentionally. It can be assumed that safe
operation is no longer possible if:
the device is visibly damaged,
the device no longer works and
the unit was stored under unfavourable conditions for a
long period of time or
it has been subjected to considerable stress in transit.
You should also heed the additional safety instructions in each
chapter of the operating instructions for the connected devices.
Never switch the device on immediately after it has been taken
from a cold into a warm environment. Condensation that forms
might destroy your device. Allow the device to reach room
temparature before switching it on.
Package Contents
Inspection camera, magnetic attachment,
hook attachment, carrying case and
operating instructions.
Description of the Parts
1 NTSC video output
2 ON/OFF switch
3 Light adjustment button „brighter“
4 Light adjustment button „darker“
5 TFT monitor
6 Battery compartment on both sides
7 Flexible gooseneck
8 Camera head with LED light
9 Hook attachment
10 Magnetic attachment
Start-up process
Never use the inspection camera for inspecting
equipment subjected to a voltage. The camera head is
made of metal and this may lead to short-circuits. For
safety reasons, de-energise all components prior to every
inspection.
Inserting/Replacing the Batteries
The inspection camera is battery-operated. Please insert new
batteries before using for the first time or when the device can no
longer be turned on. Proceed as follows to replace the batteries:
Carefully slide the rubber
protection, from the left side of the
monitor to the rear, until the battery
compartment is visible. Do not
overstretch the rubber protection.
Unscrew the battery compart-ment
and remove the cover sideways.
Now insert two new AA batteries
into the battery compartment. Pay
attention to marking. Observe the
polarity markings in the battery compartment. Close and close the
battery compartment by carefully replacing the screws. Slide the
rubber protection over the device again. Repeat these steps in the
same way on the right side.
Do not mix old and new batteries. Always replace all the
batteries at the same time. Otherwise the batteries
discharge each other. Always use batteries of the same
type and brand.
Do not leave flat batteries in the appliance. Even
batteries protected against leaking can corrode and
thus release chemicals that could be detrimental to
your health or damage the appliance. Do not leave batteries
lying around carelessly. They might be swallowed by children
or pets. If swallowed, consult a doctor immediately. Remove
