•
6
•
USING THE AIR COMPRESSOR
WARNING.
Read the instructions of the
product being inflated before using the
compressor. Avoid overinflation; do not
exceed the manufacturer’s recommended
pressures. Do not leave the air
compressor unattended during use.
1.
Remove the air compressor hose from
the storage compartment.
2.
Connect the adapter to the valve stem
by threading it onto the end. If necessary,
use one of the additional adaptors.
3.
Turn ON the inflator power switch and
inflate to the desired pressure or fullness.
4.
When the desired pressure is reached,
put the inflator power switch to OFF,
open the thumb latch and remove the
connector from the valve stem.
5.
Allow unit to cool.
6.
Recharge the unit before storing.
NOTE:
The air compressor is rated for
150 PSI maximum.
USING THE INFLATOR
RISK OF EXPLOSION.
Read instructions of the product being
inflated before using the inflator.
Avoid overinflation, do not exceed the
manufacturer’s recommended pressures.
Do not leave the inflator unattended
during use.
1.
Ensure the battery clips are securely
on the storage holders.
2.
Attach the corrugated hose with end
adapter to the high-flow inflator outlet
located near the Compressor/Inflator
switch on the back of the Instant Power.
3.
The main accessory adapter attached
to the corrugated hose accommodates
up to 4 sizes. If another size is needed,
an additional adapter can be attached to
the end of the main accessory adapter.
4.
Insert the adapter into the product to be
inflated.
5.
Push the Compressor/Inflator switch to
the INFLATOR position and inflate the
product.
6.
When the product is inflated to the
desired level, push the Compressor/
Inflator switch to the OFF position and
remove the adapter.
Estimated time for inflating
Vehicle tires 13-16"
6-24 minutes
Bike tires
1-3 minutes
Sports balls
30 seconds
These times are approximate. Use the air
compressor gauge to ensure the proper pressure
has been reached. Do not overinflate.
USING THE DEFLATOR
1.
Ensure the battery clips are securely
on the storage holders.
2.
Attach the corrugated hose with the
end adapter to the high-flow deflator
outlet, which is located on the side of
the Instant Power.
3.
The main accessory adapter attached
to the corrugated hose accommodates
up to 4 sizes. If another size is needed,
an additional adapter can be attached
to the end of the main accessory
adapter.
4.
Insert the adapter into the item to be
deflated.
5.
Push the Compressor/Inflator switch to
the INFLATOR position and deflate the
item.
6.
When the product is deflated to the
desired level, push the Compressor/
Inflator switch to the OFF position and
remove the adapter.
BEFORE USING THE CONVERTER
Important Safety Instructions:
1.
Keep the Instant Power well ventilated,
in order to properly disperse heat
generated while it is in use. Make sure
there are several inches of clearance
around the top and sides, and do not
block the vents on the back of the
Instant Power.
2.
Make sure the Instant Power is not
close to any potential source of
flammable fumes or clothing.
3.
Keep the Instant Power dry.
4.
DO NOT allow the Instant Power to
come into contact with rain or moisture.
5.
DO NOT operate the Instant Power if
you, the Instant Power, the device being
operated or any other surfaces that may
come in contact with any power source
are wet. Water and many other liquids
can conduct electricity, which may lead
to serious injury or death.
6.
Do not place the Instant Power on or
near heating vents, radiators or other
sources of heat.
7.
Do not place the Instant Power in direct
sunlight. The ideal air temperature for
operation is between 50° and 80° F.
8.
Do not use the converter near an open
engine compartment where fumes may
accumulate.
9.
Do not modify the AC receptacles in
any way.
