47
Problems
Repairs, alterations or intervention on electronic equip-
ment should only be carried out by qualified specialists.
Inexpert repairs can cause considerable damage and risk
to the user.
Only original spare parts should be used for repairs.
Please find below minor faults which you can rectify
yourself.
Error messages on the display
If the following error messages are displayed, the pro-
gramme can be restarted by pressing the start button
once the error has been rectified.
«CHILD LOCK ACTIVE»
u
Hold the Quick wash button down and press the Start
button.
«PLEASE CLOSE DOOR»
u
Push the door closed until the lock catches properly.
Start the selected programme by pressing the start button.
«CHECK WATER SUPPLY»
u
Turn on the tap and start again.
u
Filter in water supply is blocked: Clean the filter, see
chapter «Cleaning and Maintenance / Cleaning the filter
in the water inlet».
u
Interruption in water supply.
«CHECK DRAIN AND START»
u
Check whether the drainage hose is blocked.
u
Foreign bodies block the drain pum: Clean pump
according to chapter «Cleaning and Maintenance / Emer-
gency emptying».
u
The water drain provided by the customer is blocked:
Carry out an emergency discharge according to chapter
«Cleaning and Maintenance» and clean the drain siphon
(built-in siphon).
u
The position of the drain hose is too high. The maximum
pumping height is 1m above ground.
«UNBALANCE NO SPINNING»
u
Excessive imbalance. Laundry not spun
u
Press the Start button and then the Quick wash button
to end the wash programme.
u
Open the door and redistribute the load.
u
Repeat the spin cycle with the separate spin programme.
General information:
l
Avoid loading the drum with one single heavy item.
Wash large and small laundry together.
«FOAM, PROG. EXTEND»
l
The washing machine has detected foam and taken
adequate measures. The spinning cycle of the laundry
could be completed.
l
In future, please reduce the detergent quantity.
«FOAM, PROG. CANCEL»
u
Due to extremely intensive foaming, the washing
machine could not complete the spinning cycle and the
wash programme had to be aborted.
u
Repeat the wash programme without adding any
detergent.
u
In future, please reduce the detergent quantity
(if required use washing powder instead of liquid deter-
gent).
«WATER LEVEL TOO HIGH»
l
Too much foam in the washing machine, spinning has
not been effected. There are two possibilities to solve the
problem:
a)
Press the Start button and then interrupt the programme
by pressing the Quick Wash button several times until the
display «OPEN DOOR» appears.
Mix approx. 30 ml conditioner and approx. 1 litre water.
Start the previously selected wash programme (it may
take several minutes until the machine is released for the
selection of a new programme). After the water supply
has been completed, switch forward immediately to
«Conditioning» by pressing the Quick Wash button and
add the conditioner-water mixture into chamber
I
of the
detergent drawer. The programme should now end as
usually and the spinning process should take place.
Afterwards repeat the desired programme, however wi-
thout any detergent.
or
b)
Press the Start button and then interrupt the programme
by pressing the Quick Wash button several times until
the display «OPEN DOOR» appears.
Wait for approx. 1 hour and start the previously selected
wash programme, move forward immediately to «Spin-
ning» using the Quick Wash button. Usually the laundry
will be spun. If not, repeat the procedure including
waiting for 1 hour. Afterwards repeat the desired pro-
gramme, however without any detergent.
u
The maximum admissible water level is reached. Wait
until the water has been pumped out completely and
press the Start button. The programme will continue.
«WATER IS BEING PUMPED OUT»
l
Too much water is in the washing machine. Water is
pumped off to the set level.
l
If you see a lot of foam in the door glass, this means
that too much foam is in the washing machine. To
eliminate this problem proceed as for the error message
«WATER LEVEL TOO HIGH».
l
In future, please reduce the detergent quantity.
If the machine shows a function fault F – –:
u
Stop the programme with the Quick Wash button and
select a new programme.
In the event of repeated error messages:
u
Disconnect the electricity for approx. 1 minute and
then switch on again. (Withdraw the mains plug or
switch off the main building switch.)
u
The machine is ready to operate once again when the
programme pilot lamps flash.
u
Select a new programme.
If the error message still appears:
u
Make a note of the error message
u
Switch off the water tap and withdraw the mains plug
or switch off the main building switch.
u
Inform Customer Service.
Содержание Spirit topLine 7510
Страница 51: ......
