EN
21
Rinse aid and refined salt
Only use products which have been
specifically designed for dishwashers.
Do not use table salt or industrial salt, or
washing up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to
add rinse aid; however,
we recommend that you add salt,
especially if you live in an area where the water is hard
or very hard.
Follow the instructions given on the
packaging.
If you do not add salt or rinse aid, the LOW
SALT
*
and LOW RINSE AID* indicator lights
remain lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water
runs off surfaces more readily and therefore does not leave
streaks or marks.
The rinse aid dispenser should be filled:
When the LOW RINSE AID
*
indicator light on the control
panel is illuminated;
1. Open the dispenser by turning the lid
(G) in an anticlockwise direction.
2. Pour in the rinse aid, making sure it
does not overflow from the dispenser. If
this happens, clean the spill immediately
with a dry cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly
into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results,
you may adjust the quantity of rinse aid used. Use a
screwdriver to turn the dosage adjuster (F) to one of the 6
pre-set positions (the default position is set to 4):
If there are streaks on the crockery, set the adjustment
device to a lower number (1-3).
If drops of water remain on the crockery or if there are
limescale marks present after the cycle has finished, set
the adjuster to a higher number (4-6).
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of
appliance, supplies water without limescale which is then used
to wash the crockery.
This dishwasher offers a setting which helps to reduce
pollution and optimises washing performance in accordance
with the water hardness level in your area. This information can
be obtained from the organisation which supplies your
household with water.
- Switch on the appliance by pressing the
ON/OFF
button.
- Press and hold the
2
button for approximately 5 seconds;
after a short beep sounds, the water hardness setting will
appear on the display and the Start/Pause button will begin to
flash (the default water softening system setting is level
3
).
- Press the
P
button repeatedly until the desired hardness
setting has been reached (1-2-3-4-5
*
see Water hardness
table
). The selected water hardness value will appear on the
display.
E.g.: hardness setting 1 ("1" appears on the display);
hardness setting 2 ("2" appears on the display);
hardness setting 3 ("3" appears on the display); etc., etc.
up to a maximum setting of 5
*
.
- To exit the function, wait a few seconds or press one of the
option buttons
*
, or switch off the machine using the
ON/OFF
button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
(°dH = hardness measured in German degrees - °f =
hardness measured in French degrees - mmol/l = millimoles
per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash
cycle, make sure that the dispenser is never empty.
Refined salt removes limescale from the water, thus
avoiding the formation of deposits on crockery.
The salt dispenser is located in the lower part of the
dishwasher (
see Description
) and should be filled:
When the green float
*
cannot be seen by simply looking at
the cap of the salt dispenser.
When the LOW SALT
*
indicator light on the control panel is
illuminated;
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. The first time you do this: fill the water
tank right up to its edge.
3. Position the funnel
*
(
see figure)
and fill
the salt container right up to its edge (this should hold
approximately 1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel* and wipe any salt residue away from
the opening; rinse the cap under running water and then
screw it on, the head facing downwards so as to let the
water flow out of the four cracks which are arranged in a
star shape on the lower part of the cap. (the container cap
with the green float
*
)
It is advisable to perform this procedure every time you
add salt to the container.
Make sure the cap is screwed on tightly, so that no
detergent can get into the container during the wash cycle
(this could damage the water softener beyond repair).
When necessary, measure out the salt before a wash
cycle so that any saline solution which has leaked out of the
salt dispenser is removed.
*
Only available in selected models.
G
F
Water Hardness Table
°dH °fH
mmol/l
level
0 6 0 10 0 1
1
6 11 11 20 1.1 2
2
12 17
21
30 2.1
3
3
17 34 31 60 3.1 6
4
34 50 61 90 6.1 9
5
*
For values between 0
°
f and 10
°
f, we do not
recommend the use of salt.
* this setting may cause a slight increase in the
duration of the cycle.
Содержание LPE 14-308A+
