background image

12

Mounting example:

Flat head bolt (M5)

Recommended switching distance approx. 2 mm

fig. 3.4.2b

MAGNET

MAGNETIC SWITCH

ADJUSTING NUT

LOCK NUT

ANGLE BRACKET
(not included)

CYLINDER of CIRCULAR  
KNITTING MACHINE

1. Press and hold the ON/OFF key.
    The length mode settings are indicated on the display.
2. Press the DAMP key to set the desired number of machine revolutions  

    (e.g. 

 3 revolutions).

3. Insert the PROCESS MATERIAL as described in Chapter 3.4.1 and press the ON/
OFF/ZERO key.
4. On receiving the first switching pulse from the magnetic switch, the instrument  
    starts counting the defined number of revolutions, starting from zero.
    The first switching pulse from the MAGNETIC SWITCH also triggers the  
    measurement and display of the filament length.
5. After the defined number of revolutions, the instrument stops measuring the  
    filament length.
    The DISPLAY shows the measured filament length.

To start a new measurement, zero the display by pressing the  
ON/OFF/ZERO key. The previous reading is not saved.

3.4.4 Displaying the Average

  In the tension and speed modes, you can display the average of the last  
  measurement process as soon as you stop the measurement.

Requirement:
The process material has to be removed on completion of the measurement.

- Press the ON/OFF key to display the average.

After you display the average or turn off the instrument, the average cannot be 
displayed again.

3.4.3 Measuring in Length Mode (Cont.)

Содержание PT-100

















Отзывы: