manualshive.com logo in svg

Schmidt ET Series, Инструкция по эксплуатации

Поделиться
Скачать
Schmidt ET Series Скачать руководство пользователя страница 12

12

3.3.1 Charging the Battery

The battery can only be charged at a temperature b5 °C

and +45 °C.

Before you connect the AC adapter, verify that the supply voltage is correct

(100 V - 240 V).

HANS SCHMIDT & Co. GmbH provides no warranty or liability for any

damage resulting from the use of AC adapters from other manufacturers.

To charge the battery, remove the rubber stopper from the USB interface. Than connect 
the cable of the AC adapter to the USB output.
The battery can also be charged by connecting the USB cable to a PC.
When the battery is fully charged, the battery level indicator will be shown full 

.

The charging time is approx. 3 ½ hours (using the AC adapter). 

Battery overcharging is not possible

3.3.2 Switching the tension meter on

Press and hold the 

 button (for approx. 1 sec.) until the DISPLAY shows the 

measuring range, the software and hardware versions, e.g. E 1.0, and then “0”.
During startup, the tension meter performs an automatic zero adjustment. If the tension 
meter does not display zero, perform a manual zero adjustment procedure (see chapter 
3.5.2).
Holding the 

 button makes the display freeze so that you can read the measuring 

range and the software and hardware versions.

While switch-on the tension meter, make sure not to move it. Otherwise, the 

automatic zero adjustment will be faulty.

3.3.3 Switching the tension meter off

Automatic switch-off (if enabled):

- After an idle period of 3 minutes, the tension meter switches off.

Manual switch-off:

- Press and hold the 

 button for 5 seconds.

3.4  Tension meter settings

- Press the 

 and 

 buttons simultaneously to access the main menu.

- The   and   buttons can be used to select the various menu items of the main menu, 
  the submenus and the settings menus.
- Press the   button to open the selected menu; by pressing the   or 

 button you can 

  close the menu without saving changes.
- In menus with multi-digit fields (e.g. date) use the   and   buttons to move forward 
  and backward between digits.
- Press the 

 button to save the settings and exit the settings menu or press the 

 

  button to exit the current menu without saving.
- To exit the main menu press the 

 button.

Содержание ET Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды