schmersal SRB-E-204PE Скачать руководство пользователя страница 9

Страница: 9 / 12

SRB-E-204ST / SRB-E-204PE

Operating instructions

Safety-monitoring module

7.3 Start configuration SRB-E-204ST

7.3.1 Monitored start

• Manual start or activation of the module occurs when the button is

released.

Monitoring of max. actuation time 0.03 sec. … 3 sec.

If the time is exceeded, the module cannot be started!

7.3.2 Reset without monitoring / autostart

• The manual start or the activation of the module occurs when the

button is pressed (not when it is released!).

• With autostart, X2 must be bridged to +24 VDC

Not admitted without additional measure due to the risk of

gaining access by stepping behind!

Within the meaning of IEC/EN 60204-1 paragraph 9.2.5.4.2

the operating mode "automatic start" is only restrictedly

admissible. In particular, any inadvertent restart of the

machine must be prevented by other suitable measures.

+24

VDC

Reset button (detection

of the trailing edge)

Reset without monitoring /

autostart

Rotary knob position 1

Rotary knob position 6

Rotary knob position 2

Rotary knob position 7

Rotary knob position 3

Rotary knob position 8

Rotary knob position 4

Rotary knob position 9

Rotary knob position 5

Rotary knob position 10

Rotary knob position 11

Rotary knob position 12

Rotary knob position 13

Rotary knob position 14

7.4 Feedback circuit SRB-E-204ST

• Suitable for increase in capacity or number of contacts by means of

contactors or relays with positive-guided contacts. If the feedback

circuit is not required, establish a bridge.

+24

VDC

7.5 Cascading SRB-E-204PE

• Safety inputs X2 and X3 can be used for cascading of several

SRB-E-204PE modules.

• Without cascading, inputs X2 and X3 must be bridged to +24 VDC.

+24

VDC

+24

VDC

SRB-E204PE (1)

+24

VDC

X2 X3 Q1

SRB-E204PE (2)

X2 X3 Q1

SRB-E204PE (3)

X2 X3 Q1

SRB-E204PE (x)

7.6 Sensor configuration

• Different protective equipment can be monitored.

See examples as follows

• Sequence of protective equipment can be chosen freely

• Unrequired inputs S12, S22, S32, S42, S52, S62, S72, S82 must be

bridged to outputs S11, S21, S31, S41, S51, S61.

Single channel signal processing (Sensor 1 – 4)

S12 S22

S32 S42

S11/+24V

S31/+24V

S52 S62

S72 S82

S51/+24V

S61/+24V

Rotary knob

position

Function

(SRB-E-204ST)

Reset button (detection of the trailing edge)

Reset without monitoring / autostart

Dual channel signal processing NC / NC (Sensor 1 – 4)

With cross-wire monitoring

(Category 4 – PL e to ISO 13849-1 possible)

S12 S22

S11 S21

S32 S42

S31 S41

S52 S62

S51 S61

S72 S82

S51 S61

Rotary knob

position

Cross-wire

monitoring

Synchronisation

Yes

7 (SRB-E-204ST)

Yes

8 (SRB-E-204ST)

Yes

Содержание SRB-E-204PE













Результаты поиска

Содержание SRB-E-204PE

Отзывы:

Похожие инструкции для SRB-E-204PE

Бренды по названию

Популярные бренды

schmersal SRB-E-204PE, Руководство по эксплуатации

Результаты поиска

Содержание SRB-E-204PE

Отзывы:

Похожие инструкции для SRB-E-204PE

Бренды по названию

Популярные бренды