background image

E X P L O S I O N P R O O F

www.schischek.com

Schischek GmbH

 Germany, Muehlsteig 45, Gewerbegebiet Sued 5, 90579 Langenzenn, Tel. +49 9101 9081-0, Fax +49 9101 9081-77, E-Mail [email protected]

info-Max-M_en

V01 –  26-Mar-2015

Extra information for ...Max – size M

●  No power supply attached
●  The actuator is operated at ambient temperature 

beyond specifications and the internal temperature 

fuse shuts down irreversibly 

● 

Actuator does not receive sufficient supply voltage 

● 

Cable to long, voltage drop in the supply line to large

● 

The actuator has been mounted at temperatures 

< −20 °C

 and did not reach is operating temperatur 

of at least

 −20 °C 

● 

3-pos. control signal is wired on both entrances

● 

Required torque is greater than actuators torque

● 

Control signals are not attached or 

attached on a wrong conductor

● 

Actuator is incorrectly mounted and is blocked 

by an external stop unit

● 

Interchanged supply lines

● 

The actuator is operated at a too high ambient 

temperature and the internal temperature sensor 

responded 

●  ...-

BF actuators require a temperature trigger 

type ...Pro-TT or FireSafe

● 

The conversion of constant mode to 3-pos. mode 

was not set

● 

Actuators have an angle of rotation of 95° incl. 

5° pretension. While assembling the pre-load 

was not considered

● 

At start up no self-adjustment of angle of rotation 

was accomplished 

●  Attach power supply and turn on
●  Caused by inadmissable operation and for safety relevant reasons 

the actuator drove into an irreversable condition and must be ex-

changed. accompanying new installation the ambient temperature 

has to be reduced accordingly

● 

Increase line cross section or power supply

● 

Increase line cross section or power supply

● 

Ensure that a constant voltage supply is applied on conductor 1–2 

● 

Wait until the required operating temperature is achieved by the 

actuators internal heating system.The actuator will start operating 

independently 

● 

Readjust / correct circuit

● 

Adjust a higher torque at the actuator if possible otherwise 

exchange for a type with higher torque

● 

Examine rule and adjusting signals and connect in accordance 

with diagram

● 

Dismount actuator and testdrive without load for operability. Then 

install actuator accordingly so that the power transmission of the 

actuator runs the armature/damper without external blockade or 

torsion

●  Switch wires: 1 must be connected to (−, N) and wire 2 to (+, L) 

● 

Shut off actuator and let temperature decrease, reduce ambient 

temperature by suitable measures e.g. ventilation or other mount-

ing position of the actuator

●  Connect trigger, LED changes to GREEN, actuator is 

ready-to-operate

● 

Recalibrate the actuator in accordance with assembly instructions

● 

Dismount actuator off the damper, use enclosed socket wrench to 

draw up approx. 5° over the hand operated control device before 

remounting on the damper shaft. Consider assembly instructions!

● 

Accomplish self adjustment of angle of rotation in accordance with 

assembly instruction

01

 

 Actuator does not work

LED does not light

02

 

 Actuator does not work

LED lights RED

03

 

 Actuator does not work

LED lights GREEN

04

 

 Actuator does not work

LED is blinking RED

05

 

 Y-drive in 3-pos. mode cannot gear 

into intermediate positions

06

 

 Actuator sits diagonally on 

square damper shaft 

07

 

 A modulating Y-actuator working with 

reduced angle of rotation, reaches its 

end positions already at > 0 V/4 mA 

resp. < 10 V/20 mA

08

 

 LED flashes irregularly and 

actuator does not work

 Problem handling / Error indication

  Problem 

Possible cause 

Course of action

6 / 6

Содержание ExMax-50.75







Отзывы: