manualshive.com logo in svg

Schiller Grounds Care Ryan 544951H, Руководство по эксплуатации и запасным частям

Поделиться
Скачать
Schiller Grounds Care Ryan 544951H Скачать руководство пользователя страница 24

22

Jr.

Sodcutter

MAINTENANCE 

BLADE SPROCKET SHAFT

1.  Follow steps 1 thru 6 in pulley shaft section.

2.  Loosen clamp screw on left pitman arm 

C

 and 

remove from shaft.

3.  Loosen clamp screw in eccentric assembly 

D

 and 

remove.

4.  Remove two (2) top screws securing the other 

side arm assembly.  Side arm, shaft and pitman 

arm, are now removable by pulling side arm out.

5.  Remove eccentric and both bearing cages 

E

. Put 

a pan under rear portion of case to catch oil from 

case cavity.

6.  Push shaft to left of case, lift right end of shaft out 

of case with bearings and sprocket intact.

7.  To remove sprocket, press bearing from shaft, 

and slide sprocket off.

8.  Assemble in reverse procedure.  After blade 

shifter assembly is installed, adjust dog clutch 

to provide .015" (0.39 mm) clearance between 

clutch faces, as shown.

NOTE:

  End play on shaft must not exceed .005   

(.127 mm) clearance and should rotate freely when 

bearing cages are tightened.  Shim as required to 

obtain correct clearance.

9.  Apply 3M Scotch Grip 847 adhesive or equivalent 

to gear case cover before installation.

.015

(0.39 mm)

Содержание Ryan 544951H











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды