Schiller Grounds Care Ryan 544951H Скачать руководство пользователя страница 13

Страница: 13 / 42

Jr.

Sodcutter

OPERATION

STARTING THE ENGINE

1. Move the engine switch to the "ON" position.

2. Pull the recoil starter to start the engine.

3. If the choke is ON when the engine starts,

gradually back it off until the engine runs with no

choke at all.

MOVING OF UNIT

To move unit without running blade:

1. Place yellow blade shifter handle in

"disengaged" position (handle will point straight

out from unit) See

Figure 1

2. Set engine speed to slow.

3. Engage red drive shifter handle.

4. Depress black operator presence control.

5. Engage red master clutch control lever.

6. Adjust throttle to desired walking speed.

To move unit

without running the engine

, put red

drive shifter handle and red clutch control lever in

the "disengaged" position. Push unit to move it.

"DISENGAGED"

"ENGAGED"

SHIFTER HANDLE

GEAR

CASE

GEAR

CASE

SHIFTER

HANDLE

CUTTING SOD

WARNING:

Underground utilities. Electrocution,

explosion, service disruption risk.

Before beginning any work, check with the local

authorities for underground utility location and

depth. Do not operate where there is any risk

of contacting underground utilities. Contacting

buried utilities could result in a service outage.

Contacting buried electrical wires could result in

electrocution. Contacting a buried gas line could

result in an explosion.

This precaution is especially important when

using attachments such as the mole blade or

trencher which operate at greater depths.

1. Move machine to the area where sod is to be

cut. With the engine off and the red master

clutch disengaged, stand on the right side of the

machine. Loosen the green blade depth control

locking lever with your right hand, then use the

handle bar to tip the machine forward and hold it

with your left hand. Lower the yellow blade depth

control lever with your right hand until it hits the

preset depth stop. Tighten the green locking

lever.

2. Start the engine, then engage the wheel drive

and the blade drive with the red wheel drive

shifter lever and the yellow blade drive shifter

lever.

3. For straight cutting, leave the caster wheel

locking lever down. For cutting irregular or

curved shapes, raise the caster wheel locking

lever up and forward.

4. Adjust the throttle to full speed. With the

machine tipped forward, engage the red master

clutch. The machine will start moving forward

and the blade drive will operate. Lower the

machine into the sod and cut for a short distance.

5. Stop the machine and check the sod thickness.

Adjust the Depth Stop and blade if necessary.

See Adjustment section.

6. Continue cutting. At the end of each pass lift up

on the handle to raise the blade out of the sod

and turn around for the next pass.

Содержание Ryan 544951H











































Результаты поиска

Содержание Ryan 544951H

Отзывы:

Бренды по названию

Популярные бренды

Schiller Grounds Care Ryan 544951H, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание Ryan 544951H

Отзывы:

Бренды по названию

Популярные бренды