Page -10-
OPERATING INSTRUCTIONS
PREPARING FOR OPERATION
1.Check the heater for possible shipping damage. If any is
found,
immediately
notify the factory.
2.Follow all of the "Precautions".
3.Check and assure the control knob is on "OFF" position.
4. Place the gas cylinder inside the Cylinder Base, and
securely connect the regulator to the propane gas cylinder.
5.Turn the cylinder valve on. Apply a dishwashing soap
(1 part) and water (3 parts) solution to the connection at the
regulator and cylinder. Bubbles will form if the connection is
leaking.
6.In case of any leaks, turn off the propane cylinder valve,
undo the leaking connection and check & clean the
connection. Reconnect the regulator and leak test again. If
the leak persists, do not return heater to the store. Please
call toll-free
1-888-619-7060
or e-mail
for assistance and
advice.
START
1.To light the pilot, the first step is to purge the gas line
leading to the pilot assembly. Press and turn the control
knob to "HIGH" position and keep it depressed in for 1 to 2
minutes.
NOTE
: When a new or refilled gas cylinder is
installed, the heater will need to be purged again.
2.To light the pilot:
a)
Press the control knob and turn to the "PILOT" position.
b)
Hold the control knob in and press the ignition button
until the pilot lights.
c)
Keep the control knob depressed for 30 seconds to
heat the thermocouple.
d)
Release the control knob and the pilot should stay lit.
Note
: To visually check the ignition of the pilot, slide
the viewing hole cover to either side.
e)
Once the pilot flame stays on, close the viewing hole
cover.
CAUTION
: Do not attempt to slide the viewing
hole cover when the main burner is lighting, operating
or hot.
3. Set the heat level.
a)
Press and turn the control knob to "HIGH" position, the
burner will light immediately.
b)
Press and turn the control knob to the desired heat
level.
Note
: While in use, the burner flame should be
mainly blue in appearance with a small amount of
yellow.
Smoke and odor (not a gas odor) emission may occur in the
first 15 minutes of use. Run heater at high setting for at
least 15 minutes to eliminate this problem.
WARNING: If you smell gas while in use, immediately
press and turn the control knob to "OFF" position to
shutdown the heater.
STOP
1.Press and turn the control knob to "PILOT" position, the
burner will extinguish but the pilot will stay on.
2.To extinguish the pilot, press and turn the control knob to
"OFF" position.
3.Turn off gas supply.
4.Do not attempt to relight the heater for 5 minutes after the
LP cylinder valve has been closed.
RESTART AFTER SAFETY SHUTDOWN
1.Turn the gas control knob to "OFF" position.
2.Wait 5 minutes.
3.Restart following "Start" procedure.
STORAGE
1.Allow at least 45 minutes for the heater to cool down after
using.
2.Store the heater upright in a sheltered area away from
inclement weather and dust.
3.If desired, cover the heater after the heater has cooled.
4.If the heater is not to be used for an extended period of time,
disconnect and remove the Propane Gas Cylinder and store
in accordance with the "Standard for Storage and Handling
of Liquefied Petroleum Gases", ANSI/INFPA 58.
SERVICING
To assure safety, proper function and longevity of the heater,
regular maintenance is required. The frequency of maintenance
will depend on the usage of the unit. Review the following
concerning the criteria for a properly functioning heater. Failing
to follow proper, regular maintenance will void warranty.
A hazardous condition may result if a heater is used that has
been modified or is not functioning properly. When the heater is
working properly:
* The flame is contained within the heater.
* The flame is essentially blue with perhaps some yellow
tipping.
* There is no strong disagreeable odor, eye burning or other
physical discomfort.
* There is no smoke or soot internal or external to the heater.
* There are no unplanned or unexplained shut downs of the
heater.
The parts lists and wiring diagram show the heater as it was
constructed. Do not use a heater which is different from that
shown. In this regard, use only the hose, regulator and cylinder
connection fitting (called a POL fitting) supplied with the heater.
IMPORTANT
Match the color stripe on the hangtag attached to
the hose assembly with the color on the label located near the
propane inlet fitting on the heater.
Do not use alternates. For
this heater, the regulator must be set as shown in
"specifications". If there is any uncertainty about the regulator
setting, have it checked.A heater which is
not
working right must
be repaired, but
only
by a trained, experienced service person.
To find the service center closest to you, visit our website at
www.scheuco.com.or call (888) 619-7060. You may also obtain
in-warranty or out-of-warranty service by taking the product to
your local service center. In-warranty products will be repaired
with no charge for either parts or labor. Please include a brief
statement indicating date, place of purchase, the nature of the
problem and proof of purchase. Out-of-warranty products will be
repaired with a charge for parts and labor.
WARNING: FOR YOUR SAFETY
If you smell gas*:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. If odor continues, immediately call your gas
supplier.
*
See fuel safety precautions on page 2 of this
manual for more information.
Models
SPC-54PHW SPC-54PHB SPC-54PHT SPC-55PHS
Содержание SPC-54PHB
Страница 14: ......