www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
26 | GB
2.
Put the crank handle (17) on the crank holder and
use the Allen key (3) to secure the crank handle
(17).
Mounting the drilling table holder, fig. 1+8
1.
Insert the rack (E) into the groove on the drilling
table holder (18).
2.
Align the rack (E) centrally in relation to the drill
-
ing table holder (18).
3.
When bringing the rack (E) together within the
groove, ensure that the tooth meshing between the
rack and the drilling table holder (18) is correct.
4.
Now place the drilling table holder (18) with the
rack (E) on the column (2) and guide the rack (E)
into the bottom rack guide on the column foot.
5.
Use the ring (F) to secure the rack (E).
Ensure
that the rack guide on the ring (F) is pointing
downwards. Tighten the integrated Allen screw
to affix the ring (F).
6.
Screw one of the clamping handles (3) into the
drilling table holder (18).
Installing the drilling table, fig. 5
1.
Insert the drilling table (4) into the drilling table
holder (18).
2.
Use a clamping handle (3) to secure the drilling
table (4).
3.
Insert the roller support (13) into the receptacle
on the drilling table (4) and use the wing screws
(21) to secure it.
Installing the machine head and column, fig. 10
1.
Place the machine head (14) on the column (2).
2. Align the drill’s spindle with the table and the
base plate and tighten the Allen screw that is lo-
cated on the side of the machine head. (Allen key
WAF4 / C)
Installing the handles, fig. 11+12
1.
Screw three handles (10) tight in the handle
bracket’s thread.
Use the hexagon spanner (A)
to do this.
2.
Screw the remaining handle (10) into the handle
bracket for speed adjustment.
Use the hexagon
spanner (A) to do this.
Installing the folding swarf protector and the drill
chuck, fig. 13
1.
Push the folding swarf protector (11) onto the
spindle on the machine head and use a Phillips
head screwdriver to secure it.
2.
Push the tapered mandrel (22) into the drill chuck
(12) with a sharp jolt.
3.
Then push the tapered mandrel (22) into the
drill spindle.
To do this, guide the drill chuck (12)
including the cone (22) into the spindle until is
reaches the stop and then turn it until it slides a
little further into the spindle.
Vibration emissions value ah = 1,7 m/s
2
Uncertainty K = 1,5 m/s
2
The specified vibration emission value has been
measured according to a standardised testing proce-
dure and can be used for comparison of one power
tool with another; and may change depending on the
way in which the power tool is used and in excep-
tional cases may be higher than the specified value.
The specified vibration emission value can be used to
compare one power tool with another.
The specified vibration emission value can also be
used for an initial estimation of the impair.
7. Before commissioning
• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material, as well as the
packaging and transport safety devices (if pre-
sent).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, keep the packaging until the expiry of
the warranty period.
ATTENTION
The device and the packaging are not children‘s
toys!
Do not let children play with plastic bags,
films or small parts!
There is a danger of chok
-
ing or suffocating!
8.
Assembly
Column and machine foot, fig. 3
1.
Set the machine foot (1) down on the ground or
the workbench.
2.
Place the column (2) on the base plate so that
the holes on the column (2) align with the holes
on the base plate (1).
3.
Screw the four hexagonal screws (19) to fasten
the column into the base plate and tighten them
using a hexagon spanner (A).
Removing the rack, fig. 4
In order to install your drill, you must first remove the
rack (E).
1.
Use an Allen key (WAF3) to remove the ring (F)
and pull this off the column (2).
2.
Now pull the rack (F) out.
Pre-installing the drilling table holder, fig. 5+6
1.
Push the crank holder (20) through the hole in
the drilling table holder (18) from the inside.
