Scheppach 5906130901, Перевод с оригинального руководства пользователя

Страница: 80 / 108

80 GB
2. Layout (Fig. 1,2)
1. Drain plug for condensation water
2. Pressure vessel
3. Wheel
4. Supporting foot
5. Quick-lock coupling (regulated compressed air)
6. Pressure gauge (for reading the preset vessel
pressure)
7. Pressure regulator
8. ON/OFF switch
9. Transport handle
10. Quick-coupling (vessel pressure)
11. Manometer (vessel pressure)
12.
Air filter
13. Foot caps
14. Overpressure valve
3. Scope of delivery (Abb. 1-4)
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
pack aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
1x compressor
2x wheels (3)
1x air filter (12)
1x feet (4)
1x foot caps (13)
1x hexagonal screw M6 (a)
1x hexagonal nut M6 (b)
1x washer A6,4 (c)
1x spring washer A6,4 (d)
2x wheel bolts (e)
2x washer A10,4 (f)
2x spring washer A10,4 (g)
2x hexagonal nut M10 (h)
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts!
There is a risk of swallowing and suffocation!
4. Proper use
The compressor is designed to generate compressed
air for compressed-air driven tools which can be driv-
en with an air volume of up to approx. 143 l/min (e.g.
tire inflator, blow-out pistol and paint spray gun).
Due to the restricted air flow rate, it is only possible
to operate tools with a very high compressed air con-
sumption (e.g. orbital sanders, straight grinders and
impact screwdriver) in some circumstances.
1. Introduction
MANUFACTURER :
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs,
reduce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before op-
erating the machine and carefully follow its informa-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associ-
ated dangers. The minimum age requirement must
be complied with.