www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB
| 45
Fault
Possible cause
Remedy
Machine does not
start.
•
Air filter is contaminated.
•
Fuel filter is blocked.
•
Lack of fuel supply.
•
Fault in the fuel line.
•
Starting device is faulty.
•
Engine stalled.
•
Spark plug cap not attached.
•
No spark.
•
Engine faulty.
•
Carburetor faulty
•
Clean/replace the air filter.
•
Clean or renew the fuel filter.
•
Refuel.
•
Check the fuel line for kinks or damage.
•
Contact the service centre.
•
Remove the spark plug, clean and dry it; then
pull the starter rope several times; refix the
spark plug.
•
Check the correct position of the spark plug cap.
•
Clean the spark plug or replace it, if applicable.
•
Check the ignition cable for damage.
•
Contact the service centre.
Machine starts but
stops again.
•
Wrong carburetor setting (idle speed).
•
Contact the service centre.
Engine starts but the
cutting tool stops.
•
Cutting tool blocked.
•
Internal fault (drive shaft, gearbox).
•
Clutch faulty.
•
Turn off engine and remove object.
•
Contact the service centre.
•
Contact the service centre.
Machine works with
interruptions (sputter
-
ing).
•
Carburetor set up incorrectly.
•
Spark plug is sooty.
•
On/off switch faulty.
•
Contact the service centre.
•
Clean the spark plug or replace it.
•
Contact the service centre.
Smoke is generated.
•
Wrong fuel mix.
•
Carburetor set up incorrectly.
•
Use twostroke mixture at a ratio of 40:1.
•
Contact the service centre.
Machine does not
work at full power.
•
Machine is overloaded.
•
Air filter is contaminated.
•
Carburetor set up incorrectly.
•
Silencer is blocked.
•
Do not use force during mowing/trimming.
•
Clean the air filter or replace it.
•
Contact the service centre.
•
Check the exhaust.
Brush cutter does not
work at full power.
•
Blades are blunt or damaged.
•
Cut material is too high (machine
overload).
•
Sharpen or replace blades.
•
Cut the grass in phases.
Grass trimmer does
not work at full power.
•
Cutting line too short or damaged.
•
Machine is overloaded because the
grass is too high.
•
Feed more cutting line through or replace it.
•
Cut the grass in phases.
Cutting line cannot be
fed through.
•
Spool empty.
•
Replace spool.
Pole saw does not
saw, it plucks or
vibrates.
•
Chain tension too high.
•
Chain blunt.
•
Chain attached incorrectly.
•
Chain worn.
•
Check and reset chain tension.
•
Have the chain sharpened or replace it.
•
Reattach the chain.
•
Replace the chain.
Saw chain becomes
hot or saw chain lubri
-
cation does not work.
•
No oil in the tank.
•
Oil line blocked.
•
Chain tension too high.
•
Chain blunt.
•
Refill oil.
•
Clean the oil line.
•
Set the chain tension.
•
Have the chain sharpened or replace it.
Содержание 5904802907
Страница 8: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 8 50 50 S S 49 49 R ...
Страница 28: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 28 DE ...
Страница 259: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 259 ...
Страница 262: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 262 ...