www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
28 | GB
g)
Use the appropriate saw blade for the riving
knife.
For the riving knife to function properly, the
saw blade diameter must match the appropriate
riving knife and the body of the saw blade must be
thinner than the thickness of the riving knife and
the cutting width of the saw blade must be wider
than the thickness of the riving knife.
Safety information for sawing
a)
m
DANGER: Do not place your hands and
fingers in the sawing area or close to the saw
blade.
A moment of carelessness or a slip could steer
your hand towards the saw blade and result in se-
rious injuries.
b)
Only guide the workpiece against the rotational
direction of the saw blade or cutting tool.
Guid-
ing the workpiece in the same direction as the ro-
tational direction of the saw blade above the table
can lead to the workpiece and your hand being
drawn into the saw blade.
c)
When performing longitudinal cuts, never use
the mitre stop to guide the workpiece, and
when transverse cutting with the mitre stop
never additionally use the parallel stop for lon
-
gitudinal adjustment.
Simultaneously guiding
the workpiece with the parallel stop and mitre stop
increases the probability that the saw blade will
jam and kickback will result.
d)
When performing longitudinal cuts, always ap
-
ply the feed force to the workpiece between
the stop rail and the saw blade. Use a push rod
if the distance between the stop rail and saw
blade is less than 150 mm, and a push block
if the distance is less than 50 mm.
This type of
working aid ensures that your hands remain a safe
distance from the saw blade.
e)
Only use the push rod provided by the manu
-
facturer, or a push rod that has been produced
in accordance with instructions.
The push rod
ensures a sufficient distance between the hand
and saw blade.
f)
Never use a damaged or partially sawn push
rod.
A damaged push rod may break and lead to
your hand running into the saw blade.
g)
Never work “freehand”. Always use the paral
-
lel stop or the mitre stop to position and guide
the workpiece. “Freehand” means supporting
or guiding the workpiece with the hands, rath
-
er than using the parallel stop or mitre stop.
Free-handed sawing leads to incorrect alignment,
jamming and kickback.
h) Never reach around or over a turning saw
blade.
Reaching for a workpiece can lead to ac-
cidental contact with the rotating saw blade.
g)
Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed.
Use of the power tool
for operations different from those intended could
result in a hazardous situation.
h)
Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
5) Service
a)
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power
tool is maintained.
Safety instructions for table saws
Guarding related warnings
a)
Keep guards in place. Guards must be in work
-
ing order and be properly mounted.
A guard
that is loose, damaged, or is not functioning cor-
rectly must be repaired or replaced.
b) Always use saw blade guard, riving knife
and for every through–cutting operation.
For
through-cutting operations where the saw blade
cuts completely through the thickness of the work-
piece, the guard and other safety devices help re-
duce the risk of injury.
c)
After completing working procedures where
the removal of the protective cover and/or riv
-
ing knife is necessary (e.g. producing folds
and rebating, cutting grooves or cutting with
a turnover), the protective system must be im
-
mediately reattached.
The guard helps to reduce
the risk of injury.
d) Make sure the saw blade is not contacting the
guard, riving knife or the workpiece before the
switch is turned on.
Inadvertent contact of these
items with the saw blade could cause a hazardous
condition.
e)
Adjust the riving knife as described in this in
-
struction manual.
Incorrect spacing, positioning
and alignment can make the riving knife ineffective
in reducing the likelihood of kickback.
f) For the riving knife to work, they must be en-
gaged in the workpiece.
The riving knife are
ineffective when cutting workpieces that are too
short to be engaged with the riving knife. Under
these conditions a kickback cannot be prevented
by the riving knife.
Содержание 5901310901
Страница 6: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 6 23...
Страница 278: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 278...
Страница 280: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 280...
Страница 281: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 281...
