background image

 

 

 

– MAINTENANCE (ROUTINE AND EXTRAORDINARY) 

COD.

35M12/24.D.2018

 

EN 

 

THE PRESENT MANUAL BELONGS TO - 

Schenker Italia 

-  ALL RIGHTS RESERVED 

44 

 
Purge air from the 
system periodically by 
opening 

for 2-3 minutes 

the depressurization 
valve at 45°. 

   
 

 
Every 15-20 days 

 

 

 

 

6.2  Check the plant working pressure 

 
It is necessary to read the pressure on the manometer 
located  on  the  equipment  front  panel  in  order  to 
perform this verification. 
The working pressure depends on many factors such 
as  water  temperature,  salinity  level  of  seawater, 
effective  batteries  voltage,  membranes  cleaning 
degree, typology of installation. 
The  pressure,  in  normal  working  conditions,  is 
approx.  6  -7      Bars.  There  is  a  small  pressure  lost 
head, in the range of 0,2 bar, during the cycle. 

 

 

 

 

 
If the average pressure exceeds the above ranges it is necessary to check the membranes cleaning degree. 
It  is  necessary  to  perform  the  shutdown  procedure  if  the  membranes  result  dirty.  If  cleaning  also  results 
insufficient  it  could  be  necessary  to  perform  an  alkaline  washing  using  the  chemical  product  SCHENKER 
CLEANING 2 (SC2). It is recommended to contact a Schenker certified service center. 
 
 

6.3  Check for absence of leaks 

It is necessary to perform this verification at every plant start-up and however often, since possible leaks due 
to accidental causes (pipe bursting, hose clamp loosening, equipment failure, etc.) may occur, even plentiful, 
with the consequence of possible damages.  
 
 
 

6.4  Check for membranes replacement 

The reverse osmosis membranes have a 7 years average working life. It is recommended therefore, after 5 
years of operation, to verify the possible necessity of substitution and however to perform the substitution after 
7 years. 
 

6.5  Shutdown procedure 

It is necessary to perform the shutdown procedure before standstills longer than 3 months, for instance before 
the winter laying up. 
The purpose of the shutdown is to flush the system from possible organic and inorganic sediments, and inhibit 
the growth of bacteria that could reduce the reverse osmosis membranes efficiency.  
 

Содержание MODULAR 35
























































Отзывы: