manualshive.com logo in svg

Schacht 40th Anniversary Cherry Matchless Spinning Wheel, Инструкции, обслуживание и гарантия


Поделиться
Скачать
background image

Attaching the treadle support bar

Remove the leg bolt, washer and small rod from the front leg of the wheel. 

Remove the short rod from the bolt, and insert the leg bolt with the washer through 
the hole in the middle of the treadle support bar. Replace the short rod on the leg 
bolt, then insert the leg bolt into the hole in the front leg. Align the short rod with 
the slot in the front leg. Using the 4mm hex wrench, screw the leg bolt into the bar-
rel nut glued into place in the cross brace.

Attaching the treadles

Lay the wheel on its back on a table, tilted to either side. Use a towel or blanket 

to protect the table and the wheel from scratches. 

Slide the left (shorter) treadle into place, allowing the treadle to hang off the 

edge of the table. Using a Phillips screwdriver, attach the treadle hinge to the trea-
dle using the short screws in the small bag. Insert the screw at the far right and fas-
ten loosely, then insert the screw at the far left. Tighten the screw only until it stops 
turning. Go back and tighten the first screw, then insert the remaining three screws. 
Be sure not to overtighten the screws. Repeat for the right treadle.

Attaching the treadle support brace

Remove the leg bolt. Place the washer and the treadle support brace onto the 

leg bolt, then insert the leg bolt through the treadle support bar and short rod and 
into the front leg. Make sure that the short rod is aligned in the slot in the front 
leg and that the support brace angled edge is at the top. Tighten the leg bolt only 
by hand. Use the 1” screws to attach the brace to the front of the treadle sup-
port bar (see diagram). Center the treadles between the back legs of the wheel. If 
necessary, the treadle support bar can slide a bit to the left or right to center the 
treadles. Tighten the leg bolt with the 4mm hex wrench.

treadle hangs off edge of table

treadle hinge

right treadle

first screw

table

left treadle

first screw

leg bolt

treadle 

support bar

treadles

short rod

front leg

leg bolt

4mm hex 

wrench

barrel 

nut

cross brace

treadle 

support bar

washer

washer

2

Содержание 40th Anniversary Cherry Matchless Spinning Wheel













Отзывы:

Нет отзывов

Похожие инструкции для 40th Anniversary Cherry Matchless Spinning Wheel

Бренды по названию

Популярные бренды

Загрузить еще бренды