background image

 

PRACTICAL TIPS 

Point of Broadcast 

 

Ideally, the point of broadcast should be from a high point – too low to the ground will 
only limit the area covered, and therefore the success obtained. 

Volume Levels 

 

The  volume  of  broadcast  has  to  be  at  a  natural  level  for  the  birds  to  identify  the 
broadcast as a natural call: 

o

 

Too  loud  -  the  broadcast  will  merely  appear  to  sound  like  a  noise,  and  no 
reaction is likely. 

o

 

Too  quiet  -  they  simply  will  not  hear  the  call,  and  again  a  dispersal  reaction  is 
unlikely.  

 

To attain what is perceived as a natural level for the target species, begin broadcasting 
the system at the lowest volume level and then increase the volume until you see the 
birds react to the call

 

Coverage 

 

The  system  is  stated  as  providing  coverage  in  each  speaker  direction  to  a  distance  of 
100m.  

 

This is dependent on a number of factors such as the lie of the land, prevailing weather 
conditions,  strength/direction  of  wind,  other  ambient  noise,  air  temperature  and 
obstructions to sound broadcast. 

 

As such, either a greater or lesser distance may be obtained.  

 

Taking this into account, it is important to remember that the broadcast needs to sound 
at  a  natural  level  to  the  birds  for  greatest  effect  –  too  loud  or  too  quiet,  will  merely 
either sound like a noise to the target birds and be ignored, or not heard at all.  

Effect on other wildlife 

 

The calls broadcast are only recognisable by the target bird species, and therefore has 
no lasting effect on other wildlife at all.  

 

That is not to say that there will be no reaction – in some extreme cases, the broadcast 
of a distress call may for example bring in a Hawk hoping to find some easy food. 

 

Relocating the Scarecrow 180 / 360™ 

 

One  of  the  benefits  of  this  system,  if  mounted  on  a  pole/base  unit,  is  that  it  can  be 
moved from location to location from time to time to enable different problem areas to 
be tackled. 

 

Whilst this is an option, it is recommended that a system should ideally remain in situ if 
an area is required to be kept free of birds. 

 

The  concept  of  the  system  is  to  create  the  impression  over  time  that  the  area  is  a 
“threat  area”  and  one  therefore  to  avoid  –  so  over  time  the  bird  numbers  may  even 
reduce. This is achieved by the regular (but not too frequent) broadcast of the Distress 
Call, which clearly cannot be achieved if the system is relocated.  

Page 2 

Содержание SCARECROW 180


















Отзывы: