manualshive.com logo in svg

Scag Power Equipment V-Ride II, Руководство оператора

Поделиться
Скачать
Scag Power Equipment V-Ride II Скачать руководство пользователя страница 40

36

R

Section 7

 DANGER

To avoid injury from burns, allow the mower to 
cool before changing the oil and removing the 
filter.

7.5 ENGINE FUEL SYSTEM

 DANGER

To avoid injury from burns, allow the mower 
to cool before removing the fuel tank cap and 
refueling.

A. FILLING THE FUEL TANK

Fill the fuel tank to the bottom of the filler neck insert 
(approximately 7 gallons for 36" models or 8 gallons for  all 
other models indicating Full (F) on the fuel gauge) at the 
beginning of each operating day. See Figure 7-5. Do not 
overfill. Use clean, fresh unleaded gasoline with a minimum 
octane rating of 87 and a maximum of 10% Ethanol.

DO NOT use E85 Fuel. Using E85 Fuel will cause severe 
damage to the engine.

FUEL LEVEL

E

F

1/4

1/2

3/4

. .

.

.

.

FILLER NECK 

INSERT

Figure 7-5. C.A.R.B. / EPA Phase 3 Fuel Level

To avoid personal injury or property damage, use extreme 
care in handling gasoline. Gasoline is extremely flammable 
and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

2. Use only an approved gasoline container.

3. Never remove the gas cap or add fuel with the

engine running. Allow the engine to completely cool
before fueling.

4. Never fuel the machine indoors or in an enclosed

trailer.

5. Never store the machine or fuel container where

there is an open flame, spark or pilot light such as on
a water heater or other appliances.

6. Never fill containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.

7. Remove the machine from the truck or trailer and

fuel on the ground. If this is not possible, then refuel
the machine with a portable container, rather than
from a gasoline dispenser nozzle.

8. Keep the nozzle in contact with the rim of fuel tank

or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing

immediately and wash affected skin.

10. Replace gas cap and tighten the fuel cap until it

ratchets.

B. REPLACING IN-LINE FUEL FILTER
ELEMENTS

The engine fuel filter should be replaced after every 500 
hours of operation or annually, whichever occurs first.  See 
Figure 7-6.

1. Close the shutoff valve.  Locate the fuel filter and

remove the two clamps securing the fuel filter to the
fuel hose.  Remove the fuel filter.

2. Install a new fuel filter.  Be sure it is installed in the

proper direction.  Secure to the fuel hose using the
two clamps.

Содержание V-Ride II

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды