background image

4

Section 2

R

6.  DO NOT operate the machine under the influence of 

alcohol or drugs.

7.  Before and during reverse operation, look behind 

and down for small children and/or pets.

8.  If the operator(s) or mechanic(s) cannot read 

English, it is the owner's responsibility to explain this 
material to them.

9.  DO NOT wear loose fitting clothing. Loose clothing, 

jewelry, or long hair could get tangled in moving 
parts. Do not operate the machine wearing shorts; 
always wear adequate protective clothing, including 
long pants. Wearing safety glasses, safety shoes, 
and a helmet is advisable and is required by some 
local ordinances and insurance regulations.

 WARNING

Always wear hearing protection. Operating this 
machine over prolonged periods of time can 
cause loss of hearing.

10.  Keep the machine and attachments in good 

operating condition. Keep all shields and safety 
devices in place. If a shield, safety device, or decal 
is defective or damaged, repair or replace it before 
operating the machine.

 WARNING

Belts, belt guards, hoses, intake nozzles, and 
discharge tubes are subject to wear, damage, and/
or deterioration, which could expose moving parts 
or allow objects to be thrown. Frequently check 
components and replace with manufacturer's 
recommended parts when necessary.

11.  Thoroughly inspect the area where the equipment is 

to be used and remove all foreign objects.

12.  Evaluate the terrain to determine what accessories 

and attachments are needed to properly and safely 
perform the job. Use only approved attachments and 
accessories.

13.  See Section 5.3 ENGINE FUEL SYSTEM for fueling 

procedure.

14.  Use a funnel or spout to prevent spillage.

15.  Never refuel indoors.

16.  Keep flammable objects (cigarettes, matches, etc.), 

open flames, and sparks away from the fuel tank and 
fuel container. Use only approved containers.

 WARNING

Fuel is highly flammable. Take the following 
precautions:

Store fuel in containers specifically designed for 
this purpose.

Refuel outdoors only and do not smoke while 
refueling.

Add fuel before starting the engine. Never remove 
the cap on the fuel tank or add fuel while the 
engine is running or when the engine is hot.

If fuel is spilled, do not attempt to start the engine 
but move the machine away from the area of 
spillage and avoid creating any source of ignition 
until fuel vapors have disappeared.

Replace all fuel tank and container caps 
securely.

17.  Check the inlet hose, discharge, debris receiver 

box, and components frequently for signs of wear or 
deterioration. Replace as needed to prevent injury 
from thrown objects going through weak or torn 
spots.

18.  Never attempt to make any adjustments while the 

engine is running unless specifically recommended 
by the manufacturer.

19.  Check the engine mounting bolts at frequent 

intervals for proper tightness.

Содержание TLS20W-29BV






























Отзывы: