background image

13

R

Section 4

390S0138

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

Cutter Engage Switch

Figure 4-2. 

- NOTE -

A squealing noise may be heard when engaging 
or disengaging the deck drive. It is caused by the 
electric clutch plates meshing as the mower comes 
up to speed. This is normal.

To disengage the deck drive, push the switch in to 

3. 

the disengage position.

Always operate the engine at full throttle to properly 

4. 

maintain cutting speed. If the engine starts to lug 
down, reduce the forward speed and allow the 
engine to operate at maximum RPM.

HILLSIDE OPERATION

4.7 

 WARNING

DO  NOT  operate  on  steep  slopes.  ALWAYS 
FOLLOW OSHA APPROvED OPERATION.

This mower has been designed for good traction and 

1. 

stability under normal mowing conditions. However, 
caution must be used when traveling on slopes, 
especially when the grass is wet. Wet grass reduces 
traction and steering control.

To prevent tipping or loss of control, do not start or 

2. 

stop suddenly, avoid unnecessary turns and travel 
at reduced speed. If tires lose traction, disengage 
blades and proceed slowly off the slope.

Avoid sudden starts when mowing on slopes.

3. 

Travel across the slope whenever possible. Never up 

4. 

and down the slope.

Keep tires properly inflated.

5. 

PARkING THE MOWER

4.8 

Park the machine on a flat, level surface only. Do not 

1. 

park the machine on an incline.

Disengage the cutter blades.

2. 

Lock the neutral latches and shift the transmission 

3. 

into the neutral position.

Slow the engine to idle speed.

4. 

Turn the ignition key to the OFF position and remove 

5. 

the key.

AFTER OPERATION

4.9 

Wash the entire mower after each use. Do not 

1. 

use high pressure spray or direct the spray onto 
electrical components.

- IMPORTANT -

Do not wash a hot or running engine. Cold water 
will  damage  the  engine.  Use  compressed  air  to 
clean the engine if it is hot.

Keep the entire mower clean to inhibit serious heat 

2. 

damage to the engine or hydraulic oil circuit.

Check the drive belts for proper alignment and any 

3. 

signs of wear. Correct and adjust if necessary.

 DANGER

To  avoid  injury  from  burns,  allow  the  mower 
to  cool  before  removing  the  fuel  tank  cap  and 
refueling.

After the mower has cooled down, fill the fuel tank 

4. 

with fresh, clean fuel at the end of every day of 
operation. See Engine Owner's Manual for proper 
octane requirements.

Check the tire pressure. Adjust pressure if 

5. 

necessary.

Содержание SW32-481FS






















































Отзывы: