Scag Power Equipment Magnum III Скачать руководство пользователя | Manualshive

Страница: 40 / 77

background image

Section 7

38

3. Use mower deck lift switch to tilt the deck up as far as

it will go.

4. Holding the nut at the top of the blade drive pulley with

a wrench, loosen and remove the blade attachment
bolt from beneath the mower deck. Remove the
washer, blade, and top and bottom cutter blade spacers.
Be sure not to misplace any of the blade spacers.
Spacers are important to align the blades to cut evenly.

4. Install the top and bottom blade spacers, blade, washer

and the blade attachment bolt to the bottom side of the
spindle. Install the locknut to the bolt and tighten to a
torque of 75 ft-lb. The nut and bolt must be tight to
inhibit wobble in the blade, causing vibration and poor
cutting.

7.12 TIRES

Check tire pressures after every 8 hours of operation
or daily.

Caster Wheels ................................. 25 PSI

Rear Steering Wheel ........................ 15 PSI

Drive Wheels.........................................15 PSI

7.13 BODY, DECK AND UPHOLSTERY

Do not wash any portion pf the equipment
while it is hot. Do not wash the engine or
radiator, use compressed air.

1. After each use, wash the mower and deck. Use cold

water and automotive cleaners. Do not use pressure
cleaners.

2. Remove all cutter deck belt guards and clean debris

from the cutter deck.

3. Do not spray water on electrical components.

4. Use a mild soap solution or a vinyl/rubber cleaner to

clean the seat.

5. Repair damaged metal surfaces and use Scag touch-

up paint available from your authorized Scag dealer.
Wax and polish the mower for maximum paint
protection.

CAUTION:

«
...
38
39
40
41
42
...
»

Содержание Magnum III














































































Отзывы:

Нет отзывов

Похожие инструкции для Magnum III

Бренд: Weed Eater Страницы: 48

Бренд: Toro Страницы: 2

Greens King V Plus

Бренд: Jacobsen Страницы: 224

Бренд: elem Страницы: 99

Бренд: FLORABEST Страницы: 44

Бренд: Snapper Страницы: 18

Бренд: Poulan Pro Страницы: 4

Бренд: VITO GARDEN Страницы: 37

Бренд: Murray Страницы: 18

Бренд: Craftsman Страницы: 14

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 14

Бренд: Craftsman Страницы: 14

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды