manualshive.com logo in svg

Scag Power Equipment Magnum III, Руководство оператора

Поделиться
Скачать
Scag Power Equipment Magnum III Скачать руководство пользователя страница 32

Section 7

30

3. Run the engine at idle speed with the hydrostatic drive

system in neutral for five minutes.

4. Check the oil level in the hydraulic tank.  It must be 3

inches from the bottom of the fill opening.  If necessary,
add SAE 10W30 motor oil.

7.4 ENGINE OIL

A. Checking Engine Crankcase Oil Level

The engine oil level should be checked after every 8 hours
of operation or daily as instructed in the Engine Operator’s
Manual furnished with this mower.

B. Changing Engine Crankcase Oil

After the first 40 hours of operation, change the engine
crankcase oil and replace the oil filter.  Thereafter, change
the engine crankcase oil after every 100 hours of operation
or bi-weekly, whichever occurs first.  Refer to the Engine
Operator’s Manual furnished with this mower for
instructions.

C. Changing Engine Oil Filter

After the first 40 hours of operation replace the engine oil
filter.  Thereafter, replace the oil filter after every 200 hours
of operation or every month, whichever occurs first.  Refer
to Engine Operator’s Manual for instructions.

7.5 ENGINE FUEL SYSTEM

A. Filling the Fuel Tank

Fill the fuel tank at the end of each operating day to within
1 inch below the filler neck.  Do not overfill and never
allow the tank to become completely empty.  Use clean,
fresh No. 2 diesel fuel with a minimum Cetane Rating of
45.

B. Replacing In-Line Fuel Filter Element
     and the Fuel Pre-Filter

The in-line fuel filter (Figure 7-3) and the fuel pre-filter

Fuel Filter
Location

(Figure 7-4) should be replaced after every 500 hours of
operation or annually, whichever occurs first.

-IMPORTANT-

Replace the fuel filter cartridge and the pre-
filter periodically to prevent wear of the fuel
injection pump plunger or the injection nozzle
due to dirt in the fuel.

Shutoff
Valve

Pre-Filter

Figure 7-4 Fuel Pre-Filter and Shut-Off Valve

Figure 7-3 Fuel Filter

Содержание Magnum III














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды