SBM Defort 93721756 Скачать руководство пользователя страница 8

Страница: 8 / 72

KICKBACK-CAUSES

• Kickback is a sudden reaction to a pinched, bound

or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the
operator

• When the blade is pinched or bound tightly by the

kerf closing down, the blade stalls and the motor re-
action drives the unit rapidly back toward the opera-
tor

• If the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig
into the top surface of the wood causing the blade to
climb out of the kerf and jump back towards opera-
tor

KICKBACK - OPERATOR PREVENTION

Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below

• Maintain a

rm grip with both hands on the saw

and position your arms to resist kickback forces;
position your body to either side of the blade, but
not in line with the blade

(kickback could cause

the saw to jump backwards, but kickback forces can
be controlled by the operator, if proper precautions
are taken)

• When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold
the saw motionless in the material until the blade
comes to a complete stop; never attempt to
remove the saw from the work or pull the saw
backwards while the blade is in motion or kick-
back may occur

(investigate and take corrective ac-

tions to eliminate the cause of blade binding; avoid
cutting nails or screws)

• When restarting a saw in the workpiece, centre

the saw blade in the kerf and check that saw
teeth are not engaged into the material

(if saw

blade is binding, it may walk up or kickback from the
workpiece as the saw is restarted)

• Support large panels to minimize the risk of

blade pinching and kickback

(large panels tend

to sag under their own weight; supports must be
placed under the panel on both sides, near the line
of cut and near the edge of the panel)

• Do not use a dull or damaged blade

(unsharpened

or improperly set blades produce narrow kerf caus-
ing excessive friction, blade binding and kickback)

• Blade depth and bevel adjusting locking levers

must be tight and secure before making cut

(if

blade adjustment shifts while cutting, it may cause
binding and kickback)

• Use extra caution when making a plunge cut into

existing walls or other blind areas

(the protruding

blade may cut objects that can cause kickback)

WARNING

• Check lower guard for proper closing before

each use

• Do not operate the saw if lower guard does not

move freely and close instantly

• Never clamp or tie the lower guard into the open

position

• If saw is accidentally dropped, lower guard may be

bent; raise the lower guard with the retracting handle
and make sure it moves freely and does not touch
the blade or any other part, in all angles and depths
of cut

• Check the operation of the lower guard spring;

if the guard and the spring are not operating
properly, they must be serviced before use

(lower

guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up of debris)

• Lower guard should be retracted manually only

for special cuts such as plunge cuts and com-
pound cuts; raise lower guard by retracting han-
dle and as soon as blade enters the material, the
lower guard must be released

(for all other sawing,

the lower guard should operate automatically)

• Always observe that the lower guard is covering

the blade before placing saw down on bench or

oor

(an unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its
path; be aware of the time it takes for the blade to
stop after switch is released)

• Avoid damage that can be caused by screws, nails

and other elements in your workpiece; remove them
before you start cutting

• When you put away the tool, switch off the motor and

ensure that all moving parts have come to a com-
plete standstill

• Use completely unrolled and safe extension cords