background image

9                                                                                                 Manual | Rinjani Kit

Assembling instruction

Part list (each cabinet)

:

- High frequency driver SATORI TW29R (sold separately)

.................

- Low frequency drivers 6½” SATORI MW16P-8 (sold separately)

.....

- Rinjani kit crossover (sold separately)

............................................

- Hex socket screw M4 x 20mm (for drivers)

....................................

- Hex socket screw M4 x 30mm (for pedestal)

.................................

- Countersunk screw M4 x 20mm (for terminal plate)

.....................

- Wood screw 4 x 16 mm for crossover (from kit crossover)

............

- Insert nut M4 (Installed )

..............................................................

- Stainless Terminal plate

.................................................................

- Binding post

.................................................................................

- Seal gasket (for terminal plate)

.....................................................

- Seal gasket (for pedestal, installed on cabinet)

.............................

- Port "are (installed on cabinet)

.....................................................

- Port paper tube (installed on cabinet)

...........................................

- Damping

.......................................................................................

- Name plate

...................................................................................

- Tweeter grill

..................................................................................

- Woofer grill

..................................................................................

Tools needed:

- Hex key 3mm size (for driver screw)
- Hex key 2.5mm size (for terminal plate screw)
- Philips screwdriver no. 2 (for crossover screw)
- Soldering iron + tin (for soldering input wire to terminal)
- Hot melt glue gun(for attaching the damping and sealing the wire hole)

1 pc
2 pcs
1 pc
18 pcs
12 pcs
4 pcs
6 pcs
34 pcs
1 pc
1 pair
1 pc
1 pc
2 pcs
2 pcs
1 pc
1pc
1 pc
2 pcs

Содержание Rinjani Kit

















Отзывы: