Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This LED driver is Double Insulated and
does not require connection to an Earth
circuit.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge.
This light fitting should be connected to a fused circuit.
This LED driver contains non-replaceable parts and
cannot be serviced. If damage occurs the part should
be scrapped.
This product cannot be dimmed.
This product is rated at IP20.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
Specification
Input Voltage
:
220V – 240V 50 – 60Hz a.c
Output Voltage
:
12W 12V d.c. 1.0A Max Constant Voltage
Cable
:
0.75 to 2.5mm squared
Operating Temp :
-20˚C to +50˚C
Case Temp (tc) :
85˚C
Power Factor
:
0.8
Layout
• Plan the desired layout of this fitting carefully,
ensuring the cables will reach the distances between
the LED driver and each LED fitting.
• Ensure that there is adequate ventilation for the LED
driver.
• Avoid locating any cables in positions that would
cause a hazard. Position cables away from areas
where they may be at risk from being cut, trapped or
damaged.
• Cables that are to be in walls must be protected
using suitable conduit or plastic trunking.
• When laying the cables out be aware that voltage
drop on the low voltage side can be a factor. Use a
good quality low resistance cable and arrange the
layout so that the mains cable is the longer length.
We recommend that a maximum total cable length of
5.0m is used on the low voltage side.
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting, carefully note the position of each set
of wires.
• Position the LED driver next to the mains outlet that
the system will connect to. Do not connect at this
stage. Ensure that the LED driver can be accessed
for any future maintenance requirements.
• Remove the cover to access the wiring terminals.
Pay particular attention as to which is mains (PRI)
and which is the low voltage side (SEC).
• Connect the low voltage wiring first. Connect the red
wire to the positive terminal, and the black wire to
the negative terminal.
• Ensure that the connections are tight, and that no
loose strands have been left out of the connection
block.
• Connect the mains supply wiring, ensuring that
brown cable (Live) goes to the L connector and that
the blue cable (Neutral) goes to the N connector.
• Ensure that the connections are tight, and that no
loose strands have been left out of the connection
block.
• Replace the cover ensuring that the cable is gripped
properly.
Direct Wiring
This LED driver is double insulated and must not be
earthed.
• The LED Driver can also be fitted to a rewireable 3
pin plug fitted with a 3 amp fuse. Should the fuse
require replacement, it must be replaced with a fuse
rated at 3 amp and approved to BS1362.
• If the mains plug is unsuitable for the socket outlet
or is removed for any other reason, then the cut off
plug should be disposed of safely to prevent the
hazard of electric shock.
• There is a danger of electric shock if the cut off plug
is inserted into any 13 amp socket outlet.
• The wires in the mains lead on this appliance are
coloured in accordance with the following code:
Blue – Neutral
Brown – Live
• Use a 3 Amp Fuse approved to BS1362.
E
L
N
Fuse
3 Amps
Cord Clamp
BLUE
Neutral
BROWN
Live
Plug Wiring
Check that...
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection
block.
43810 - LED Driver.indd 3-4
11/05/2012 10:28:44
