Sawmaster R1040 Скачать руководство пользователя страница 24

Страница: 24 / 31

Troubleshooting

Problem

Possible Cause

Solution

Machine does not run when switched

Power cord not properly

ﬁ

xed/

plugged in

Check that the machine is properly

connected to the power supply

Power cord defective

Have the power cord checked, re-

place if necessary

Main power switch defective

Have the main power switch checked

and replace if necessary by a quali-

ﬁed electrician

Loose electrical connection inside

the electric system

Have the whole electric system of

the machine checked by a quali

ﬁ

electrician

Motor defective

Have the motor checked and re-

placed if necessary by a quali

ﬁ

technician

Motor stops (power cut out)

Too much pressure exerted while

cutting

Exert less pressure when cutting

Incorrect speciﬁcation for saw blade

Use a saw blade which corresponds

to the material being cut

Saw has a defective electric system

Have the electric system of the saw

checked by a quali

ﬁ

ed technician

Poor machine performance, little

power

Power cord/extension cable too long

or cable still wound up inside cable

drum

Use a power cord/extension cable of

the rated length, use a cable drum

with cable fully extended

Power network is insuf

ﬁ

cient

Observe the electrical ratings of the

machine and connect it only to a

power network which complies with

these ratings

Drive motor no longer runs at rated

speed (RPM)

Have the motor checked by a quali-

ﬁed electrician and have it replaced if

necessary

Содержание R1040
































Результаты поиска

Содержание R1040

Отзывы:

Похожие инструкции для R1040

Бренды по названию

Популярные бренды

Sawmaster R1040, Руководство пользователя

Результаты поиска

Содержание R1040

Отзывы:

Похожие инструкции для R1040

Бренды по названию

Популярные бренды