sauermann E INSTRUMENTS 1500 Скачать руководство пользователя страница 21

Страница: 21 / 170

K000000000EJ 032433 210519

7.5.1 Gas sampling probe

General description

The gas sampling probe is made of a stainless steel tube with a plastic hand grip and includes an internal K-type

thermocouple (Ni-NiCr) for measuring the gas temperature of the gas.

The thermocouple is located in the probe tip. It is connected to the instrument via a compensated cable running

in a specific slot of the rubber hose of the sample probe.

The compensation of the cold junction is performed with a Pt100 RTD (Resistance Temperature Detector) that

measures the temperature in correspondence of the thermocouple connector. The K-type thermocouple (Ni-NiCr)

allows continuous measurements at high temperatures. The instrument has another internal Pt100 RTD for

measuring the internal temperature; this sensor is also used for measuring the ambient temperature. In case you

wish to detect the temperature of the combustion air directly into the intake duct you will have to use the Tc-K

type optional remote sensor. It is suggested to perform this measurement to carry out the calculation of the

efficiency of the system when the temperature of the combustion air is different than the temperature of the

environment where the instrument is positioned.

Technical features:

Temperature sensor:

K-type thermocouple (Ni-NiCr) - IEC584 - class 1

Pneumatic connectors: Pressure:

Male - diameter 3.5 inches

Gas input:

Male - 0,31 inches diameter

Temperature sensor connector:

TC-K mignon

Tube:

Material:

EPDM

Adaptor for pockets:

Material:

Galvanized steel

External diameter: 0.39 .. 0.87 inches

Handle:

Material:

Nylon

Color:

Black

Tip:

Material:

AISI 304 stainless steel

Diameter:

0.31 inches

WARNING: in case of measurement of very high temperatures it is recommended to remove the tip

slowly in order to let it cool down without suffering heat stress; once extracted from the measurement

point do not place it on a cold surface, otherwise this could affect the internal temperature sensor; in

case of failure of the thermocouple it is possible to replace the bare element with a compensated cable

(see section 17 ‘Spare parts and service’).

7.5.2 Smoke sampling probe for average CO measurement

This probe, is made up by an INOX AISI 304 steel multi-perforated stiff tip, provided with a positionable well

adapter, it allows to take the smoke from different spots of the stack, so to obtain the average CO measure.

The smoke temperature is measured through a thermocouple type K (Ni-NiCr) inserted in the probe tip. This is

connected to the instrument through a compensated cable inserted in a proper seat of the smoke sampling probe

rubber pipe. Because of the technical construction of the tip, the internal thermocouple does not detect

immediately the correct smoke temperature. The compensation of the cold junction is made with a Pt100

thermoresistance which detect the temperature in correspondence of the thermocouple connector. The

thermocouple type K (Ni-NiCr) allows continuous measures at high temperatures. This probe can be also used

for the combustion analysis.

Technical specifications

Temperature sensor:

Thermocouple type K (Ni-NiCr) - IEC584 - class 1

Pneumatic connectors:

Male- diameter 0.35 inches pressure connection

Male - diameter 0.31 inches gas entrance connection

Temperature sensor connector:

TC-K mignon

Tube:

Material:

EPDM

Length:

6.6 ft

Well adapter:

Material:

Galvanized steel

External diameter: 0.39 .. 0.87 inches

Handle:

Material:

Nylon

Color:

Black

Tip:

Material:

stainless steel AISI 304

Diameter:

0.31 inches

Length:

11.8 inches

Working temperature:

max. 1112°F

CODE

TIP LENGTH

EPDM TUBE LENGTH

MAXIMUM WORKING TEMPERATURE

AASF62A 300 mm // 11.8 inches

3 m // 9.8 ft.

1112°F - immersion depth 6.3 inches

AASF65A 750 mm // 29.5 inches

3 m // 9.8 ft.

1472°F - immersion depth 19.6 inches

Содержание E INSTRUMENTS 1500











































































































































































Результаты поиска

Содержание E INSTRUMENTS 1500

Отзывы:

Похожие инструкции для E INSTRUMENTS 1500

Бренды по названию

Популярные бренды

sauermann E INSTRUMENTS 1500, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание E INSTRUMENTS 1500

Отзывы:

Похожие инструкции для E INSTRUMENTS 1500

Бренды по названию

Популярные бренды