Satex SA 235 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

Satex SA 235 Скачать руководство пользователя страница 6

Manual SA 235

page 6

Two weight margins can be entered: the down limit and the up limit.

If the weight value is:

- higher as the up limit, Led "HI" lights up

- in between the up and down limit, Led "OK" lights up

- lower as the down limit, Led "LO" lights up

This weight control works for a gross, as well as for a tared (net) weight reading.
In the user mode a "beep" sound may be connected to the weight margins.

The accuracy of  the margins is based upon the High Resolution weight reading, even if this is not the
actual selected weight reading.

Note:
The check-weighing function cannot be active in the piece counting mode. Both function cannot be active at
the same time.
First switch off the selected mode (key         > 2 sec.) and switch off the scale. Switch the scale on again and
select the required mode.

Before entering the weight margins, the weigh platform has to be empty
and the reading at gross zero: the         Led should light up and the Led
above        should be off.

1. Press key         continuously and then press key          > 2 seconds,

until the display shows:

rANG

. Now release both the keys.

2. Press again key           in order to enter the "Low" weightvalue margin,
    the Led next to "LO" lights up.

2. The flashing figure may be increased with cursor key         .

With cursor key the next to the right figure can be selected.

3. Confirm the entered weightvalue with enter key         . The display
    now switches to input of the "High" weightvalue margin,
    the Led next to "HI" lights up.

4.  Enter the "High" weightvalue margin in the same way.

5. Confirm the entered weightvalue with enter key         . The display
    switches off and the checkweigh mode is started.

6. With key          the checkweigh mode can be switched off temporarily

and back on again.

If temporarily switched off, all 3 the Leds light up, indicating that the

checkweigh mode is still active.

7. By pressing key for longer than 2 seconds, the weight margins

are deleted and the function is switched off.

WEEGTECHNIEK HOLLAND B.V.

Website www.satex.nl

Tel +31 36 522 20 30

Patroonsweg 23

Email [email protected]

Fax +31 36 522 20 60

3892 DA ZEEWOLDE The Netherlands

Check weighing

( check weighing with 2 settable weight margins)

lb

kg

g

lb

kg

g

⊳

⊳

⊳

⊳

HI

⊳

⊳

⊳

⊳

OK

⊳

⊳

⊳

⊳

LO

⊳

⊳

⊳

⊳

HI

⊳

⊳

⊳

⊳

OK

⊳

⊳

⊳

⊳

LO

lb

kg

g

⊳

⊳

⊳

⊳

HI

⊳

⊳

⊳

⊳

OK

⊳

⊳

⊳

⊳

LO

lb

kg

g

lb

kg

g

⊳

⊳

⊳

⊳

HI

⊳

⊳

⊳

⊳

OK

⊳

⊳

⊳

⊳

LO

«
...
4
5
6
7
8
...
»

Содержание SA 235













Отзывы:

Нет отзывов