Satel SENNET DL150 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 87

Satel SENNET DL150 Скачать руководство пользователя страница 4

CONT

E

N

T

Dataloggers SenNet DL150 / DL151 / DL170 / DL171 / DL172 Technical Manual

4

Satel Spain

Version 1.01

Connection of the RF and Z-Wave antennas (both optional) ........................................................ 26

USB / Wi-Fi port connection ................................................................................................................ 26

Ethernet port connection ...................................................................................................................... 26

Connection of the electricity meters ................................................................................................... 26

Preliminary considerations for connecting the electricity meters ................................... 27

Configuration as 3 three-phase meters ................................................................................ 28

Configuration as 9 single-phase meters ................................................................................ 29

Configuration as a combination of three-phase and single-phase meters..................... 34

Current transformers and Rogowski coils ............................................................................ 35

Connection of the DL-170 ............................................................................................................................. 37

Connection to the power supply .......................................................................................................... 37

Connection of the antennas: GPRS/3G, Z-Wave (optional) and RF ............................................. 37

USB / Wi-Fi port connection ................................................................................................................ 38

Ethernet port connection ...................................................................................................................... 38

GSM / GPRS port connection ............................................................................................................... 38

Digital outputs connection .................................................................................................................... 38

RS485 port connection .......................................................................................................................... 39

Connection of the DL-171 ............................................................................................................................. 41

Connection to the power supply .......................................................................................................... 41

Connection of the antennas: GPRS/3G, Z-Wave (optional) and RF ............................................. 41

USB / Wi-Fi port connection ................................................................................................................ 41

Ethernet port connection ...................................................................................................................... 41

GSM/GPRS port connection ................................................................................................................. 41

Digital-outputs connection .................................................................................................................... 41

Connection of the electricity meters ................................................................................................... 41

Connection of the DL172 .............................................................................................................................. 42

Connection to the power supply .......................................................................................................... 42

Connection of the antennas: GPRS/3G, Z-Wave (optional) and RF ............................................. 42

Ethernet port connection ...................................................................................................................... 42

GSM/GPRS port connection ................................................................................................................. 42

Digital outputs connection .................................................................................................................... 42

Connection of the electricity meters ................................................................................................... 42

SETTING ...................................................................................................................................... 45

interface ............................................................................................................ 46

Main interface menu .................................................................................................................................. 47

.................................................................................................................. 48

.............................................................................................................................. 49

................................................................................................................................... 50

Menu“Internal

ABC method ..................................................................................................... 51

“Configuration”

................................................................................................................................ 54

General parameters ............................................................................................................................ 55

«
...
2
3
4
5
6
...
»

Содержание SENNET DL150
























































































Отзывы:

Нет отзывов