background image

SATEL PERFECTA-T 

23 

Maximum current consumption from battery 

PERFECTA-T 32 .................................................................130 mA 
PERFECTA-T 32-WRL ........................................................160 mA 

Power supply output voltage.............................................................................. 12 V DC ±15% 
Power supply output voltage range.................................................................10.5 V…14 V DC 
Power supply output current .................................................................................................2 A 
Battery charging current.................................................................................................500 mA 
Battery failure voltage threshold ...............................................................................11 V ±10% 
Battery cut-off voltage............................................................................................10.5 V ±10% 
High-current programmable outputs ........................................................... 1000 mA / 12 V DC 
Low-current programmable outputs ................................................................ 25 mA / 12 V DC 
KPD output ................................................................................................... 500 mA / 12 V DC 
AUX output ................................................................................................... 500 mA / 12 V DC 
Hardwired programmable zones.............................................................................................. 8 
Maximum number of programmable zones............................................................................ 32 
Hardwired programmable outputs............................................................................................ 4 
Maximum number of programmable outputs ......................................................................... 16 
Power supply outputs .............................................................................................................. 2 
Communication buses ............................................................................................................. 1 
Keypads.......................................................................................................................... up to 4 
Partitions.................................................................................................................................. 2 
Telephone numbers for messaging ......................................................................................... 8 
Voice messages .................................................................................................................... 16 
Users ..................................................................................................................................... 15 
Timers...................................................................................................................................... 8 
Event log............................................................................................................................ 3584 
Security grade according to EN50131 .......................................................................... Grade 2 
Environmental class accor
Operating temperature ran

 humidity..........................................................................................................93±3% 

Electronics board dimensio

PERFECTA-T 32-WRL ............................................. 160 x 110 mm 

ding to EN50130-5 ......................................................................... II 

ge................................................................................. -10…+55 °C 

Maximum

ns 

PERFECTA-T 32 ........................................................ 160 x 68 mm 

Weight 

PERFECTA-T 32 .................................................................... 100 g 
PERFECTA-T 32-WRL ........................................................... 110 g 

8.2  PRF-LCD keypad 

Supply voltage ................................................................................................... 12 V DC ±15% 
Standby current consumption ..........................................................................................30 mA 
Maximum current consumption........................................................................................50 mA 
Environmental class according to EN50130-5 ......................................................................... II 
Operating temperature range................................................................................. -10…+55 °C 
Maximum humidity..........................................................................................................93±3% 

Содержание PERFECTA 16




























Отзывы: