CONNECTIONS
Q
What you need
Peripheral equipment (such as monitor, digital video recorder or time-
lapse VCR)
Cables for connecting peripheral equipment and camera (coaxial cables,
connecting plugs)
Power adapter (AC 24 V or DC 12 V)
Q
Supported coaxial cables
You can use any of the following coaxial cables:
RG-59U (3C-2V) Length: 250 m max.
RG-6U (5C-2V) Length: 500 m max.
RG-11U (7C-2V) Length: 600 m max.
When using an RG-59U (3C-2V) cable, do not use it on piping or air
wiring.
Select the cable according to the distance between the devices you wish
to connect.
If you use a cable other than the types above, the image or sync signal
will be attenuated and will not be transmitted correctly.
Q
Making connections
1
Connect the camera and peripheral equipment.
2
Connect the power cable.
<When using an AC 24 V adapter>
Connect 3 wire grounded cable (use 18AWG+) as shown in Figure 1.
To prevent a fire hazard use any UL listed wire rated VW-1 for the AC
24 V cable input terminal.
<When using a DC 12 V adapter>
Check that the polarity is correct and connect the cable as shown in
Figure 2.
3
Insert the power adapter plug into the wall outlet.
The POWER indicator (red) lights.
CAMERA INSTALLATION
Q
Camera attachment bracket
The camera attachment bracket can be reconfigured as shown in Figure
above depending on the installation environment. As per design, use the
removed screws.
NOTE:
When monitoring lighting or other extremely bright objects (which exceed
the maximum required illumination), smearing may occur in the vertical
or horizontal direction (either above and below the high-brightness object
or as a perpendicular band). In such a case, adjust the angle of
illumination and other factors while observing the monitor.
When using the camera attachment stand (sold separately), select a
location that will be able to withstand the weight of the camera and stand
for many years, and fix them securely in place.
Q
Flange-back adjustment
This normally does not need adjustment. If the picture is out of focus at the
telephoto position, adjust the flange-back position as described below.
1
Loosen the LOCK screw.
2
Set to the maximum telephoto position
and focus the picture using the focus
ring.
3
Set to the maximum wide-angle
position and focus the picture using
the flange-back adjustment dial.
4
Repeat steps 2 and 3 if the image does
not stay in focus when changing from
a wide-angle shot to a telephoto shot.
5
When the setting is complete, tighten
the LOCK screw.
CAMERA ADJUSTMENTS/SETTINGS
The camera comes pre-adjusted and ready to install at time of factory
shipment, but you may want to make adjustments or settings to adapt to the
operating conditions or installation environment.
If you have trouble adjusting the camera, consult your dealer or an
Authorized Sanyo Service Center.
(
= Factory default setting)
Q
Iris setting
Change iris setting when using either lens below.
CONNECTIONS AND INSTALLATION
EI
HI
CENT
MANU
LL
AI
NORM
MULT
INT
WB
ATW
BLC
OFF
PHASE
LEVEL
R
B
GND AC24V
DC12V
GND AC24V
DC12V
L
H
VIDEO OUT
POWER
CONNECTIONS
Monitor
Digital video recorder
or time-lapse VCR
: VIDEO IN
CAMERA INSTALLATION
Camera screws (Shorter)
CAMERA ADJUSTMENTS/SETTINGS
Figure 2
Figure 1
AC 24 V connection
3
3
2
1
DC 12 V connection
2
: VIDEO OUT
Bracket screws (Longer)
EI
(for indoor use)
When using a manual or fixed iris lens and the electronic iris
function is on.
• Set the lens aperture to the shortest F stop.
AI
When using an auto-iris lens.
LOCK
1
NOTE on EI setting:
If fluorescent lighting is used where the camera is installed, the object will
flicker as a result. This type of phenomenon can be avoided by replacing
the fluorescent lighting with incandescent lamps.
If the light entering the lens exceeds the maximum required illumination,
the image cannot be displayed properly. In that case, manually adjust the
lens iris.
Q
Gain control
For adjusting the sensitivity of the camera. Use this setting for shooting in
dark environments.
NOTE:
The HI setting causes noise generation and a grainy image.
Q
BLC: Backlight compensation
This camera has three different backlight compensation modes. Change
the mode to match the backlight condition.
NOTE on multi-spot metering:
If the background of the object is extremely dark, set to center-weighted
metering mode.
Q
WB: White balance (color compensation)
Q
Sync setting
(Only when using an AC 24 V adapter)
NOTE:
When using a DC 12 V adapter, the sync setting is set to Internal sync.
Q
LEVEL: Lens iris dial
If the entire image is too dark or too bright when using an auto-iris lens,
adjust the contrast using the LEVEL dial (
).
ADJUSTMENTS AND SETTINGS
HI
Increased sensitivity allows shots to be taken in dark environments.
NORM
Normal setting
Multi-spot metering: normal mode
When applying backlight compensation
to the entire screen.
Multi-spot metering: high mode
When applying more backlight
compensation than normal mode.
Center-weighted metering
When applying backlight compensation
to only the central portion of the screen.
OFF
This function is off.
2
3 34
MANU
Lets you fine-tune the white balance manually.
WB
• R (Red) dial
: Turn clockwise to augment screen red.
• B (Blue) dial
: Turn clockwise to augment screen blue.
ATW
Compensation is performed automatically.
LL
Line-Lock: Synchronizes the unit with power frequency when two or more
cameras are connected via a switcher unit.
When the image on the monitor rolls vertically, adjust the phase.
•If using this unit as the second or subsequent camera;
Adjust the roll by turning the PHASE dial
.
•If using this unit as the first camera;
Adjust the roll using the phase adjuster on the second and subsequent
cameras.
INT
Internal sync
L (Counterclockwise)
Closes the lens iris, making the entire image darker.
H (Clockwise)
Opens the lens iris, making the entire image brighter.
55 5
R 5
B
R
B
6 7
7
58
8
OBLIGATIONS
In order to obtain warranty service, the product must be delivered to and picked up from an
Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in
this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained
by calling the toll-free number listed below.
THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN
THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND
PROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL
PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR
RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE
CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.
Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company
warrants this SANYO product against defects in materials and workmanship for the periods
specified below. SFC will repair or replace (at its option) the product and any of its parts which fail
to conform to this warranty. The warranty period commences on the date the product was first
purchased or rented at retail.
SANYO INDUSTRIAL VIDEO
COLOR CCD CAMERA LIMITED WARRANTY
For product operation, authorized service center referral, service assistance or problem
resolution, call
CUSTOMER INFORMATION 1-800-421-5013
Weekdays 8:30 AM – 5:00 PM Pacific Time
For accessories and/or parts, call
PARTS ORDER INFORMATION 1-800-726-9662
Weekdays 8:30 AM – 5:00 PM Pacific Time
LABOR
PARTS
IMAGE DEVICE
3 YEARS
3 YEARS
3 YEARS
EXCLUSIONS
This warranty does not cover (A) the adjustment of customer-operated controls as explained in
the appropriate model's instruction manual, or (B) the repair of any product whose serial number
has been altered, defaced or removed.
This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.
This warranty does not apply to uncrating, setup, installation, removal of the product for repair or
reinstallation of the product after repair.
This warranty does not apply to repairs or replacements necessitated by any cause beyond the
control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting
from unauthorized service or parts, improper maintenance, operation contrary to furnished
instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse,
neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and
tear.
The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize
any party to assume for it any other obligation or liability.
SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO
THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN
NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY
DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO
CAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES AND
DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN
CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING
WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER
SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
ATTENTION
For your protection in the event of theft or loss of this product, please fill in the information below
for your own personal records.
Model No.
Serial No.
(Located on back or bottom side of unit.)
Date of Purchase
Purchase Price
Where Purchased
e_l5ax4_us_7.fm Page 2 Friday, April 23, 2004 2:13 PM
