background image

 

Title 

Specifications of Lithium Ion battery (Prismatic Type) 

page 

7/13 

9. Storage Condition 

9-1 Storage Temperature and Humidity(less than 3 months) 

  Store  the  cell  at  temperature  range  -20~+35

,  low  humidity(less  than  70%RH)  and  no 

corrosive gas atmosphere. 

  No condensation on the cell 

9-2 Long Period Storage 

  In  case  of  long  period  storage,  store  the  cell  at  temperature  range  -20~+20

,  low 

humidity(less than 70%RH), no corrosive gas atmosphere. 
And  in  this  case,  charge  condition  of  the  cell  is  SANYO  shipment  charge  state  or 
discharge state. 

  No condensation on the cell. 

 

10. Precautions on Handling Lithium Ion Cells 

In term of shipping and assembling the battery pack, this chapter describes precautions on 
handling SANYO lithium ion cells, which are assembled for PDA’s battery packs by Nexcon 
Technology Co., Ltd.. This battery pack consists of UF103450P. 

10-1 Expiration Date 

 

Assemble single cell into battery pack within 1 month after delivery. 

10-2 Precautions on Series Connection of Cell 

  When the cells are connected in series, use same lot number, same shipping charge date 

and same capacity rank cells, and use within 20mV voltage difference. 

 

Lot  number,  shipping  charge  date  and  capacity  rank  are  on  carton  label  when  SANYO 
shipping for series. 

When the cells are connected in series, the discharge end voltage should be 3.0V/cell. 

 

10-3 Precautions on Terminals of Cell 

  Do not over-stress or rotate at positive terminal plate and negative cap. 

By over-stress, it has possibility to remove the welding point and cause leakage or short 
circuit. 

10-4 Inspection before Shipment of the Battery Pack 

  About  all  battery  pack,  inspect  voltage,  internal  impedance  and  function  of  protection 

circuit before shipment. 

10-5 Packing and Shipping Cells 

  When  cells  are  re-shipped  to  assembling  factory,  make  enough  attention  the  packing  to 

avoid stress by shipping. 
SANYO recommends the same package shipped from SANYO when re-shipping. 
Even  if  after  open  package,  when  re-shipping,  use  the  same  parts  and  materials  from 
SANYO for re-packing. 

10-6 Abnormal Cell 

  Do not use abnormal cell which has damages by shipping stress, drop, short or something 

else, and which gives off electrolyte odor. 

 
 

File  No 

UF103450-849 

Energy Company, SANYO Electric Co., Ltd. 

Portable Rechargeable Battery Business Group 

Lithium-Ion  Battery  Business  Unit 

Содержание UF103450P-NETE-5
















Отзывы: