background image

ENGLISH

Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours. There is the possibility that the previous screen has been
fixed. Pay attention sufficient when you use LCD Monitor.

You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.

Contact your dealer for the backlight replacement when the screen is dark, flickering
or not lighting up. Never attempt to replace it by yourself.

Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.

If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer.

For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
To protect the LCD panel, do not scratch or rub the screen with a hard object.

Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.

Thinner
Benzine
Abrasive cleaner

Spray-type cleaner
Wax
Acid or Alkaline solvent

Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.

Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.

The following symptoms are normal with LCD monitors and do not indicate a problem.

NOTE

When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture
position to its correct position.

n

n

n

SPECIAL NOTES ON LCD MONITORS

3     FOR YOR SAFETY

n

n

WARNING

n

CAUTION

n

NOTE

n
n

n

CABINET

LCD
SCREEN

CLEANING

Содержание PLL405WP-B0X1
















Отзывы: