Sanyo PLC-XU8, Руководство по обслуживанию

Страница: 29 / 120

-29-
Electrical Adjustments
Gain adjustment [component]
1. Enter the service mode.
2. Receive the 16-step grey scale 480i-component signal
with
computer2 [component]
mode.
3. Connect an oscilloscope to test point “
tP35G
” (+) and
chassis ground (-).
4. Select group no. “
0
”, item no. “
3
” and adjust the ampli-
tude “
a
” to be minimum by changing the Data value.
(a)
White Level
1. Enter the service mode.
2. Receive the 16-step grey scale composite video sig-
nal with
Video [Video]
mode.
3. To start the auto-calibration for Component adjust-
ment, select group no. “
260
”, item no. “
0
” and then
change data value from “
0
” to “
1
”. After the auto-cal-
bration completed, "OK" will appear on the screen.
b
Auto Calibration adjustment [Video]
1. Enter the service mode,
2. Receive the 16-step gray scale computer signal with
computer2 [rGB]
mode.
3. Select group no. “
100
” item no. “
7
” (Red) or “
8
” (Blue),
and change Data values respectively to make a prop-
er white balance.
Confirm that the same white balance is obtained in video
and computer input.
,
White Balance adjustment [PC]
1. Enter the service mode.
2. Receive the 16-step grey scale computer signal with
computer2 [rGB]
mode.
3. Connect an oscilloscope to test point “
tP35G
” (+)
and chassis ground (-).
4. Select group no. “
100
”, item no. “
6
” and change data
value to adjust amplitude “
a
” to be
1.6 ±0.1V
.
(a)
white level
white level
m
50% White adjustment [PC]
Gain adjustment [Video]
1. Enter the service mode.
2. Receive the 16-step grey scale composite video signal
with
Video [Video]
mode.
3. Connect an oscilloscope to test point “
tP35G
” (+) and
chassis ground (-).
4. Select group no. “
0
”, item no. “
3
” and adjust the ampli-
tude “
a
” to be minimum by changing the Data value.
5. Connect an oscilloscope to test point “
tP35r
” (+) and
chassis ground (-).
6. Select group no. “
0
”, item no. “
4
” and adjust the ampli-
tude “
a
” to be minimum by changing the Data value.
7. Connect an oscilloscope to test point “
tP35B
” (+) and
chassis ground (-).
8. Select group no. “
0
”, item no. “
5
” and adjust the ampli-
tude “
a
” to be minimum by changing the Data value.
(a)
White Level
1. Enter the service mode.
2. Receive the 50%-Whole Gray computer signal with
computer2 [rGB] mode.
3. Select group no. “
100
”, item no. “
92
” and change
data value to “
2
” to reduce the panel frequency.
4. Project only green light component to the screen.
5. Select group no. “
101
”, item no. “
1
” and change data
value to obtain the minimum flicker on the screen.
6. Project only red light component to the screen.
7. Select item no. “
0
” and change data value to obtain
the minimum flicker on the screen.
8. Project only blue light component to the screen.
9. Select item no. “
2
and change data value to obtain
the minimum flicker on the screen.
10. Select group no. “
100
”, item no. “
92
” and change
data value to “
0
” to reset the panel frequency.
n
Common Center adjustment
below adjustment is performed when the above auto
calibration is failed.