Sanyo 437 644 00, Руководство по обслуживанию

Страница: 16 / 36

‑ 15 ‑
A.REMOVING PRIMARY INTERLOCK SWITCH A.REMOVING PRIMARY INTERLOCK SWITCH
A.REMOVING PRIMARY INTERLOCK SWITCH A.REMOVING PRIMARY INTERLOCK SWITCH
A.REMOVING PRIMARY INTERLOCK SWITCH
(See Figure 1 on page 1)
(1)Disconnect all lead wires from the pri‑
mary interlock switch.
(2)Remove
2 screws securing the
lever stopper.
(3)Remove 1 screw securing the switches.
Then pull out the switches.
(4)Make necessary adjustment,and make micro‑
wave energy leakage check according to
1.ADJUSTMENT PROCEDURE FOR SWITCHES on
page 1,after it is replaced with new one,
check proper operation of it according to
CHECKOUT ROCEDURE FOR
SWITCHES on page
6.
(See Figure on page 1)
8. DISASSEMBLY INSTRUCTIONS 8. DISASSEMBLY INSTRUCTIONS
8. DISASSEMBLY INSTRUCTIONS 8. DISASSEMBLY INSTRUCTIONS
8. DISASSEMBLY INSTRUCTIONS
‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL ‑ OVEN MUST BE DISCONNECTED FROM ELECTRICAL
OUTLET WHEN MAKING REPLACEMENTS, REPAIRS,
OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, OUTLET WHEN MAKING REPLACEMENTS, REPAIRS, OUTLET WHEN MAKING REPLACEMENTS, REPAIRS,
ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑
ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑ ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑ ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑ ADJUSTMENT AND CONTINUITY CHECKS BEFORE PRO‑
CEEDING WITH ANY REPAIR WORK AFTER DISCON‑
CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ CEEDING WITH ANY REPAIR WORK AFTER DISCON‑ CEEDING WITH ANY REPAIR WORK AFTER DISCON‑
NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE
NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE NECTING, WAIT AT LEAST 1 MINUTE, UNTIL THE
CAPACITOR IN THE HIGH‑VOLTAGE AREA HAS FULLY
CAPACITOR IN THE HIGH‑VOLTAGE AREA HAS FULLY CAPACITOR IN THE HIGH‑VOLTAGE AREA HAS FULLY CAPACITOR IN THE HIGH‑VOLTAGE AREA HAS FULLY CAPACITOR IN THE HIGH‑VOLTAGE AREA HAS FULLY
DISCHARGED.
DISCHARGED. DISCHARGED. DISCHARGED. DISCHARGED.
C.REMOVING FUSE C.REMOVING FUSE
C.REMOVING FUSE C.REMOVING FUSE
C.REMOVING FUSE
Remove the 15A fuse with screwdriver.
NOTES
NOTES NOTES NOTES NOTES
‑ When replacing the 15A fuse, be sure to use
an exact repair part.
‑ If the 15A fuse blows immediately, check
the interlock switch, the relay 3 and 4 (on
the control circuit board) and the inter
lock monitor switch according to CHECKOUT
PROCEDURE FOR SWITCHES on page 8. And make
sure to check the microwave energy leakage
according to 1. ADJUSTMENT PROCEDURE FOR
SWITCHES on page 1, when the interlock
switch, the relay 3 and 4 or the interlock
monitor switch is adjusted or replaced.
‑ If the primary interlock switch,the relay
3 and 4 or the interlock monitor switch
operate properly,determine which of the
followings is defective : control circuit
board,blower motor,gear motor,high voltage
transformer,high voltage capacitor,high
voltage diode or magnetron.
‑If the high voltage diode is defective,
replace not only the high voltage diode
but also the fuse diode.
WHEN REPLACING ANY DOOR MICROSWITCH, WHEN REPLACING ANY DOOR MICROSWITCH,
WHEN REPLACING ANY DOOR MICROSWITCH, WHEN REPLACING ANY DOOR MICROSWITCH,
WHEN REPLACING ANY DOOR MICROSWITCH,
REPLACE WITH THE SAME TYPE SWITCH
REPLACE WITH THE SAME TYPE SWITCH
REPLACE WITH THE SAME TYPE SWITCH REPLACE WITH THE SAME TYPE SWITCH
REPLACE WITH THE SAME TYPE SWITCH
SPECIFIED ON THE PARTS LIST.
SPECIFIED ON THE PARTS LIST.
SPECIFIED ON THE PARTS LIST. SPECIFIED ON THE PARTS LIST.
SPECIFIED ON THE PARTS LIST.
(See Figure on page 1)
(1)Disconnect all lead wires from the inter‑
lock monitor switch and door sensing switch.
(2)Remove 1 screw securing these switches.
Then pull out the switches.
(3)Make the necessary adjustments or placement
of switch by the reversing step(2)and check
to microwave energy leakage according to
1.ADJUSTMENT PROCEDURE FOR SWITCHES on
page
1
. After it is replaced with the new
one,check with the new one,check proper
operation of it according to
CHECKOUT PRO‑
CEDURE FOR SWITCHES
on page 8.
B.REMOVING INTERLOCK MONITOR AND DOOR SENSING B.REMOVING INTERLOCK MONITOR AND DOOR SENSING
B.REMOVING INTERLOCK MONITOR AND DOOR SENSING B.REMOVING INTERLOCK MONITOR AND DOOR SENSING
B.REMOVING INTERLOCK MONITOR AND DOOR SENSING
SWITCH SWITCH
SWITCH SWITCH
SWITCH
D. D.
D. D. D.REMOVING CABINET
REMOVING CABINET
REMOVING CABINET REMOVING CABINET REMOVING CABINET
(1)Remove 4 screws of the side securing the
cabinet to the oven cavity.
(2)Remove 5 screws of the rear side securing
the cabinet to the oven cavity.
(3)Remove the cabinet from the main body by
pushing and sliding the cabinet backwards.