●Setting availability is different to use Program Mode,
MULTI-SETTING GEAR, AUX, and CODE10.
①
Setting by Program Mode
In case of connecting to SSL port, D01 - 06 apply to CODE1 - 6.
②
Setting by Multi-Setting Gear
③
Setting by AUX function
■Available to set contents by AUX-ADJ
④
Setting by CODE10
*1 GAIN/QUICK/SPD-FW/SPD-RT/GY-LIM/AVE-FL
●Please check light for current SGS-02 condition.
*Setting REVERSE on transmitter will be
switched green and blue light in LIMIT MODE.
〇
→On
△
→Flashing
☆
→Blinking
－
→Off
Setting
Steps
Service and Support
●Servo does not work.
In case of flashing blue and green light, SGS-02 works in PROGRAM MODE and servo will not work.
Please finish Program Mode or restart car.
In case of using servo is incompatible with SXR responses mode and turn on SXR-OUT setting, Servo does not work.
Please turn off SXR-OUT function by Program Mode or MULTI-SETTING GEAR.
●Servo cannot point neutral position.
In case of setting gyro limit and QUICK setting value is above 1, neutral disposition might be happened.
Please set QUICK value is “0” when setting gyro limit.
●Gyro does not work.
SGS-02 GYRO-GAIN might set “0”. Please check GYRO-GAIN setting by Program Mode or MULTI-SETTING GEAR.
Also, please check CODE1 setting is not “0” in case of using CODE10 by transmitter.
●Servo hunting
In case Boost and Stretcher values in Programmable servo (PGS servos) set high values, hunting will be happened.
Please use the servo to decrease Boost and Stretcher values.
In another case is gyro works by car vibration.
SGS-02 is structured to avoid effect by car vibration. If the SGS-02 worked by the vibration, please use
thick double side tape or place the SGS-02 apart from car motor.
●Please refer SGS-02 Setting in the below.
●Please refer in the below PGS servo setting for drift.
*Please start to try default setting except the above setting.
Setting Contents Setting Range
① ② ③
④
SSL-CH
5 - 8
○
×
×
×
×
×
×
×
×
×
×
×
■
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
REVERSE
NOR/REV
SXR-OUT
ON/OFF
AUX-ADJ
※1
GAIN-LV
×0.5 / 1.0
GAIN
○
CODE1
QUICK
○
CODE2
SPD-FW
M01
M02
M03
M04
D01
D02
D03
D04
D05
D06
○
CODE3
SPD-RT
○
CODE4
GY-LIM
○
CODE5
AVE-FL
○
CODE6
0
-
100%
LED
SW
LED
LED
(Default)
Limit Mode
MODE
Operation
Mode
Program
Mode
Blue Red
Green
☆
☆
☆
☆
☆
☆
△
△
〇
〇
〇
〇
〇
〇
〇
〇
-
-
-
-
-
-
〇
〇
〇
〇
〇
〇
△
△
△
△
CONDITION
No signal from transmitter
Start Limit Mode
Complete a side steering setting
Complete an another side steering setting
Finish Limit Mode Setting
Operate by internal setting
Operate by internal s AUX
Operate by CODE10
Program Mode
Set Up Mode
Finish Set Up Mode
△
Contents
PGS-LH/LH2
PGS-CL/CL2
STRECT
Contents
MV-FRQ
MV-HLD
5
-
10
100
0
10
-
20
100
0
In case car does not turn well during the corner by increased GAIN value
For Drift
For F1
Car will be stable to increase GAIN value.
*Servo might be hunting to increase GAIN value.
Please set not to be hunting.
Gyro maximum movement is limited by
increased GY-LIM value.
Counter maximum will be limited to
adjust cornering during the drifting.
Gyro maximum movement is limited to
increase GY-LIM value.
Car turn well during tight corner even if
cannot turn by only gyro operation.
Hunting will be decreased to increase the value.
AVE-FL averaged gyro function, gyro works
will be slowly.
Gyro movement will be slowly to increase
FW and RT setting values.
Basically, set closed values for
both FW and RT.
Basically do not use the function for F1
Basically do not use the function for F1
Car does not turn well to increase GAIN value.
Please increase QUICK value to turn well without decreasing GAIN value.
GAIN
QUICK
AVE-FL
GY-LIM
SPD
(FW/RT)
In case of servo hunting (as vibration)
In case of feeling gyro is too fast
In case of being real car movement
In case of feeling counter is strong
In case of feeling not turn during tight corner
In case car is not stable during the corner
List for Setting Contents
List for LED Light Indication
Trouble Shooting
Flow Chart for Gyro Setting
PGS Servo Recommendation for Drift
5
6
BRAKE
50 (Default)
30 - 40