Example of the Connection for SGS-02
①
Setting by PROGRAM MODE
● In case of setting by program mode
1. Please connect gyro as the below picture. LED light will be turned on blue after turning on the transmitter and car.
2. Press SW with holding for 2 second. LED will be flashing green and blue light and will be in program mode.
3. In the program mode, press SW to move setting contents:
①
→
②
→
③
4. Please press SW with holding for 2 seconds on the setting contents. Mode will be in setup mode and can set select setting content.
5. In setup mode, red and green light will be flashing. Press SW to set values:
#1→#2→#3.
6. Press SW with holding for 2 seconds and setting value will be changed.
7. When finished setting value, mode will be returned on program mode.
8. Press SW to change setting content after
⑩
, the program mode will be finished and save setting value to SGS-02.
●
SGS-02 is different to set up by using device function.
In case of setting GAIN, QUICK, SPD-FW, SPD-RT, GY-LIM, and AVE-FIL, Please refer in the below.
*Please also check devices are compatible with CODE10 and SSL function on SANWA HP.
●In Program Mode Indication
Blue Light flashing Times: Setting contents
Green Light Flashing Times: Setting values
●In Setting Mode Indication
Red and Green Light Flashing Times: Setting Contents
Press SW to move setting values: #1→#2
Press SW to move setting contents:
①
→
②...⑩
, then return to operation mode after
⑩
・・・・・・・・・
Press SW with holding for 2 seconds to be SET UP MODE (Red and Green Light will be flashing)
Press SW with holding for 2 seconds
Press SW with holding for 2 seconds to be PROGRAM MODE (Green and Blue Light will be flashing)
To return Operation Mode is setting value will be saved in SGS-02
After finished setting, mode will be back to the Program Mode.
Finished
Operation Mode
Program Mode
Set Up Mode
Holding SW
LED
SW
SW
Press
*In case of connecting AUX/SSL input connector to receiver SSL port, Program Mode can be set only
①～④
*In case of not connecting SXR compatible servo, please DO NOT turn on SXR-OUT function.
*In case of turning on the SXR-OUT function, please restart the car. The setting will not apply until restart.
Program Mode Contents List
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
NOR
REV
OFF
ON
GAIN
QUICK
SPD-FW SPD-RT
GY-LIM
AVE-FL
×0.5
×1.0
90%
100%
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
0%
10%
20%
30%
40%
50%
60%
70%
80%
#: Green Light Flashing Times
Setting Contents
REVERSE
SXR-OUT
AUX-ADJ
GAIN-LV
GAIN
QUICK
SPD-FW
SPD-RT
GY-LIM
AVE-FL
Blue Light
Flashing Times
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
（Example）REVERSE Setting Change
①
REVERSE
②
SXR-OUT
LED
SW
To SX Port
Battery Box
Connect steering data input connector
#1
NOR
#2
REV
Turn on Blue Light
LED
SW
Servo
×
CH1 on Receiver
Connection
③
Setting by AUX Function
●In case of setting by AUX function(*required more than 3ch transmitter and receiver),
setting will be available by transmitter.
Connect AUX/SSL port to receiver CH3 or CH4.
When turning on the car, SGS-02 light will be turned on blue and red.
Default setting is GAIN setting.
Connecting to receiver CH3 can be set by AUX1. Connecting to receiver CH4 can be set by AUX2.
AUX setting depends on transmitters. Please check transmitter’ s manual.
■To change AUX-ADJ setting by PROGRAM MODE or MULTI-SETTING GEAR, AUX can change to set for
QUICK, SPD-FW, SPD-RT, GY-LIM, or AVE-FL.
*AUX response mode is only available with NOR or SHR.
④
Setting by CODE10
●In case of setting by CODE10(*required transmitter and receiver are compatible with CODE10),
Setting will be available by transmitter CODE10 function.
1. Connect SGS-02 AUX/SSL input connector to receiver SSL port.
2. Transmitter AUX2 set CODE10.
3. Check SGS-02 Light is turned on green and blue.
4. Set each setting value by AUX2 CODE 1 - 6.
■How to save setting by CODE10
Setting data by CODE10 can be saved in SGS-02.
After setting value by CODE10, enter in program mode. Then finished program mode will be saved CODE10 setting in the SGS-02.
In case of using saved data, please take off SSL/AUX connector from receiver SSL port, then restart car.
Please check green light will be off when restarted.
*CODE5 is not compatible with SGS-02
*SXR response mode is not available to use CODE10.
*SSL-CH set “5” as default setting. Basically, the SSL-CH is not needed to change. Please keep SSL-CH setting is “5”.
●In case of not connecting AUX or device is not compatible with AUX
①
PROGRAM MODE
②
MULTI-SETTING GEAR
2CH Transmitter
Transmitter is incompatible
with CODE10
Receiver do not have SSL port
*In case of using FH5 RF mode
Transmitter is compatible
with CODE10
Receiver is compatible with SSL
①
PROGRAM MODE
②
MULTI-SETTING GEAR
③
AUX
④
CODE 10
Connection
How to Set
Example devices
●In case of using SSL/CODE10
情
LED
SW
Servo
×
Receiver CH1
LED
SW
Servo
Receiver SSL Port
Receiver CH1
●In case device is compatible with AUX
LED
SW
Receiver CH3 or 4
Receiver CH1
②
Setting by MULTI-SETTING GEAR
●In case of setting by MULTI-SETTING GEAR(Optional),
setting will be available to connect setting data input connector
to MULTI-SETTING GEAR.
*Please also check how to use MULTI-SETTING GEAR on SANWA HP.
Setting values can be set 0~100 by MULTI-SETTING GEAR.
(Default
: )
SW Press
Servo
3
4