Sanwa cd732 Скачать руководство пользователя страница 3

Страница: 3 / 36

To ensure that the meter is used safely, Be sure to observe the

instruction when using the instrument.
1. Never use meter on the electric circuit that exceed 6 kVA.

2. Pay special attention when measuring the voltage of AC 33 Vrms

(46.7 Vpeak) or DC 70 V or more to avoid injury.

3. Never apply an input signals exceeding the maximum rating

input value.

4. Never use meter for measuring the line connected with

equipment (i.e. motors) that generates induced or surge

voltage since it may exceed the maximum allowable voltage.

This instruction manual explains how to use your multimeter

CD732 safely. Before use, please read this manual thoroughly.

After reading it, keep it together with the product for reference to it

when necessary.

Using this product in ways not specified in this manual may

damage its protection function.

The instruction given under the heading " WARNING" " CAUTION"

must be followed to prevent accidental burn or electrical shock.

1-1 Explanation of Warning Symbols

The meaning of the symbols used in this manual and attached to

the product is as follows.

: Very important instruction for safe use.

・

The warning messages are intended to prevent accidents to

operating personnel such as burn and electrical shock.

・

The caution messages are intended to prevent damage to the

instrument.

: Dangerous voltage (Take care not to get an electric shock

involtage measurement.)

: DC

: AC

: Resistance

: Buzzer

: Diode

: Line frequency

: Duty ratio

: Capacitor

: Plus

: Minus

: Double insulation

: Fuse

: Ground

1-2 Warning Instruction for safe use

Duty

–

【

】

SAFETY PRECAUTIONS : Before use, read the following safety precautions

WARNING

– 32 –

Содержание cd732





































Результаты поиска

Содержание cd732

Отзывы:

Похожие инструкции для cd732

Бренды по названию

Популярные бренды

Sanwa cd732, Инструкция по эксплуатации

Результаты поиска

Содержание cd732

Отзывы:

Похожие инструкции для cd732

Бренды по названию

Популярные бренды