Sanuvox R MAX Скачать руководство пользователя страница 7

Страница: 7 / 16

Instruction Manual for R Max

1-888-726-8869

www.sanuvox.com

OPERATION

How to Operate your Product

The R Max is an automatic unit: once it’s installed and plugged in, simply press the power switch to turn it ON. Wait approximately

40 seconds for the startup phase to be done and enjoy clean air in your home!

CAUTION:

The suggested operating temperature range is 10 to 50°C (50 to 122°F). Operating the R Max outside this range

will result in decreased performance. For optimal performance, air temperature moving through the reaction chamber should be

in the range of 15 to 20°C (60 to 70°F).

How to Read the LCD Screen Display

The R Max’s LCD Screen Display will give you real time status update about your unit and its lamp.

Air Flow Deactivated

(Factory Settings)

Ideal Operating Conditions

Air Flow Activated

Replace Lamp Function

Start-Up

Operation

Ballast Failure

Example

Lamp Failure

Example

Stand-By

The number of days displayed in the images above are for reference only.

Содержание R MAX

















Результаты поиска

Содержание R MAX

Отзывы:

Похожие инструкции для R MAX

Бренды по названию

Популярные бренды

Sanuvox R MAX, Инструкция по эксплуатации

Результаты поиска

Содержание R MAX

Отзывы:

Похожие инструкции для R MAX

Бренды по названию

Популярные бренды